8679490000
WAS5 PRO RTD 1000
2448100000
| Delivery status: | This article will no longer be available in the future. |
| Available until: | 2019-12-31 |
| Type: | WAS5 PRO RTD 1000 |
| Order No.: | 8679490000 |
| Version: | RTD isolating transformer, Screw connection |
| GTIN (EAN): | 4032248813094 |
| Qty.: | 1 pc(s). |
| Length: | 92.4 mm |
| Length (inches): | 3.638 inch |
| Width: | 17.5 mm |
| Width (inches): | 0.689 inch |
| Depth: | 112.4 mm |
| Depth (inches): | 4.425 inch |
| Weight: | 100 g |
| Net weight: | 103.3 g |
| Operating temperature, max.: | 55 °C |
| Operating temperature, min.: | 0 °C |
| Storage temperature, max.: | 85 °C |
| Storage temperature, min.: | -20 °C |
| Operating temperature: | 0 °C...55 °C |
| Storage temperature: | -20 °C...85 °C |
| MTTF: | 267 Years |
| REACH SVHC: | Lead 7439-92-1 |
| Number of inputs: | 1 |
| Sensor: | Ni1000/2-/3-/4-wire, Potentiometer: min. 0-1kΩ, max. 0-100kΩ, PT1000/2-/3-/4-wire, Resistance: 0-4.5kΩ |
| Line resistance in measuring circuit: | 50 Ω for 3- and 4-conductor |
| Temperature input range: | Configurable, PT1000: -200°C…850 °C, NI1000: -60°C…+250 °C |
| Number of outputs: | 1 |
| Output voltage, note: | 0...10 V |
| Output current: | 0...20 mA, 4...20 mA |
| Wire break detection: | LED flashing (output value: > 20 mA, >10 V) |
| Fine adjustment: | ± 12.5 % of FSR; potentiometer: ± 12.5 % ... ± 25 % |
| load impedance voltage: | ≥ 1 kΩ |
| Load impedance current: | ≤ 600 Ω |
| Offset voltage: | max. 0.05 V |
| Offset current: | max. 100 µA |
| Status indicator: | Module active: LED on/ wire breakage: LED flashing/Error: LED off |
| Accuracy: | < 0.3 % of measured value |
| Configuration: | DIP switch, Potentiometer |
| Current-carrying capacity of cross-connect.: | ≤ 2 A |
| Galvanic isolation: | 3-way isolator |
| Input/Output: | configurable |
| Linearity: | Yes |
| Rail: | TS 35 |
| Step response time: | Fast/slow:2-/3-/4-conductor: 1.2s/2.3s; potentiometer: 0.5s/1.2s |
| Temperature coefficient: | Measuring range ≥ 200K and resistant measurement: <= 200 ppm/K of measuring range; 100< = measuring range < 200K: < = 250ppm vo |
| Voltage supply: | 24 V DC ± 20 % |
| Clearance & creepage distances: | ≥ 3 mm |
| EMC standards: | EN 55011, EN 61000-6 |
| Galvanic isolation: | 3-way isolator |
| Impulse withstand voltage: | 4 kV |
| Pollution severity: | 2 |
| Rated voltage: | 300 V |
| Surge voltage category: | III |
| Type of connection: | Screw connection |
| Stripping length, rated connection: | 7 mm |
| Tightening torque, min.: | 0.4 Nm |
| Tightening torque, max.: | 0.5 Nm |
| Clamping range, rated connection: | 2.5 mm² |
| Clamping range, min.: | 0.5 mm² |
| Clamping range, max.: | 2.5 mm² |
| ETIM 6.0: | EC002919 |
| ETIM 7.0: | EC002919 |
| eClass 9.0: | 27-21-01-29 |
| eClass 9.1: | 27-21-01-29 |
| eClass 10.0: | 27-21-01-29 |
| UNSPSC: | 30-21-18-01 |
| ROHS: | Conform |
| Delivery status: | This article will no longer be available in the future. |
| Available until: | 2019-12-31 |
| Type: | WAS5 PRO RTD 1000 |
| Order No.: | 8679490000 |
| Version: | RTD isolating transformer, Screw connection |
| GTIN (EAN): | 4032248813094 |
| Qty.: | 1 pc(s). |
| Length: | 92.4 mm |
| Length (inches): | 3.638 inch |
| Width: | 17.5 mm |
| Width (inches): | 0.689 inch |
| Depth: | 112.4 mm |
| Depth (inches): | 4.425 inch |
| Weight: | 100 g |
| Net weight: | 103.3 g |
| Operating temperature, max.: | 55 °C |
| Operating temperature, min.: | 0 °C |
| Storage temperature, max.: | 85 °C |
| Storage temperature, min.: | -20 °C |
| Operating temperature: | 0 °C...55 °C |
| Storage temperature: | -20 °C...85 °C |
| MTTF: | 267 Years |
| REACH SVHC: | Lead 7439-92-1 |
| Number of inputs: | 1 |
| Sensor: | Ni1000/2-/3-/4-wire, Potentiometer: min. 0-1kΩ, max. 0-100kΩ, PT1000/2-/3-/4-wire, Resistance: 0-4.5kΩ |
| Line resistance in measuring circuit: | 50 Ω for 3- and 4-conductor |
| Temperature input range: | Configurable, PT1000: -200°C…850 °C, NI1000: -60°C…+250 °C |
| Number of outputs: | 1 |
| Output voltage, note: | 0...10 V |
| Output current: | 0...20 mA, 4...20 mA |
| Wire break detection: | LED flashing (output value: > 20 mA, >10 V) |
| Fine adjustment: | ± 12.5 % of FSR; potentiometer: ± 12.5 % ... ± 25 % |
| load impedance voltage: | ≥ 1 kΩ |
| Load impedance current: | ≤ 600 Ω |
| Offset voltage: | max. 0.05 V |
| Offset current: | max. 100 µA |
| Status indicator: | Module active: LED on/ wire breakage: LED flashing/Error: LED off |
| Accuracy: | < 0.3 % of measured value |
| Configuration: | DIP switch, Potentiometer |
| Current-carrying capacity of cross-connect.: | ≤ 2 A |
| Galvanic isolation: | 3-way isolator |
| Input/Output: | configurable |
| Linearity: | Yes |
| Rail: | TS 35 |
| Step response time: | Fast/slow:2-/3-/4-conductor: 1.2s/2.3s; potentiometer: 0.5s/1.2s |
| Temperature coefficient: | Measuring range ≥ 200K and resistant measurement: <= 200 ppm/K of measuring range; 100< = measuring range < 200K: < = 250ppm vo |
| Voltage supply: | 24 V DC ± 20 % |
| Clearance & creepage distances: | ≥ 3 mm |
| EMC standards: | EN 55011, EN 61000-6 |
| Galvanic isolation: | 3-way isolator |
| Impulse withstand voltage: | 4 kV |
| Pollution severity: | 2 |
| Rated voltage: | 300 V |
| Surge voltage category: | III |
| Type of connection: | Screw connection |
| Stripping length, rated connection: | 7 mm |
| Tightening torque, min.: | 0.4 Nm |
| Tightening torque, max.: | 0.5 Nm |
| Clamping range, rated connection: | 2.5 mm² |
| Clamping range, min.: | 0.5 mm² |
| Clamping range, max.: | 2.5 mm² |
| ETIM 6.0: | EC002919 |
| ETIM 7.0: | EC002919 |
| eClass 9.0: | 27-21-01-29 |
| eClass 9.1: | 27-21-01-29 |
| eClass 10.0: | 27-21-01-29 |
| UNSPSC: | 30-21-18-01 |
| ROHS: | Conform |
| ECCN: | |
| Country of Origin: | DE |
| EAN: | 4032248813094 |
| Weight: | 0.00 kg |
| Length: | 0.00 m |
| Width: | 0.00 m |
| Height: | 0.00 m |