View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Select language
1-Click Quote Request
Product
Pepperl+Fuchs
243729
HIC2883
Request a Quote
Pepperl+Fuchs 243729
HIC2883
Solenoid Driver
On Request. Please send us an email to inquire the price and avaliability.
"ucnguBrctvdgcxgt0eqo"
Description
1-channel isolated barrier, 24 V DC supply (bus or loop powered), Output 45 mA at 12 V DC, Line fault transparency (LFT), Test pulse immunity, Up to SIL 3 acc. to IEC 61508pa. This isolated barrier is used for intrinsic safety applications. It supplies power to solenoids, LEDs and audible alarms located in a hazardous area. The device is controlled with a loop powered signal or a bus powered logic signal. The device is immune to the test pulses of various control systems. The device simulates a minimum load at the input. The minimum load can be activated and de-activated. The line fault transparency function can display a line fault in the field by a change in impedance at the switching input of the solenoid driver. The line fault transparency function is only available, if the device is supplied via the termination board.
Technical parameters
| Signal type: | Digital Output |
| Safety Integrity Level (SIL): | SIL 3 |
| Connection: | SL1: 1a, 1b(-); 2a, 2b(+) |
| Rated voltage: | 19 ... 30 V bus powered via Termination Board 19 ... 30 V loop powered via input , reverse polarity protected |
| Input current: | 75 mA at 24 V, 270 Ω load |
| Power dissipation: | 1.3 W at 24 V, 270 Ω load |
| Connection side: | control side |
| Connection: | SL1: 7a(-), 9a(-); 8a(+), 10a(+) |
| Test pulse length: | max. 2 ms from DO card |
| Signal level: | loop powered 1-signal: 19 ... 30 V DC 0-signal: 0 ... 5 V DC bus powered 1-signal: 15 ... 30 V DC (current limited at 5 mA) 0-signal: 0 ... 5 V DC |
| Rated current: | 0-signal: typ. 1.6 mA at 1.5 V DC; typ. 8 mA at 3 V DC (maximum leakage current DO card) 1-signal: ≥ 36 mA (minimum load current DO card) |
| Inrush current: | < 200 mA , 10 ms loop powered |
| Connection side: | field side |
| Connection: | SL2: 5a(+), 5b(-) |
| Internal resistor: | approx. 240 Ω |
| Current: | typ. 45 mA |
| Voltage: | ≥ 12 V |
| Current limit: | 50 mA |
| Open loop voltage: | typ. 24.6 V |
| Load: | nominal 0.05 ... 18 kΩ |
| Switching frequency: | max. 10 Hz |
| Energized/De-energized delay: | 20 ms / 5 ms |
| Line fault detection: | signal at short-circuit Rload < 25 Ω, lead breakage Rload > 50 kΩ ; test current < 500 µA |
| Connection: | SL1: 6b |
| Output type: | open collector transistor (internal fault bus) |
| Output/other circuits: | basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Display elements: | LEDs |
| Control elements: | DIP-switch |
| Configuration: | via DIP switches |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2012 , EN 61326-3-2:2008 For further information see system description. |
| Degree of protection: | IEC 60529:2013 |
| Protection against electrical shock: | EN 61010-1:2010 |
| Ambient temperature: | -20 ... 70 °C (-4 ... 158 °F) Observe the temperature range limited by derating, see section derating. |
| Degree of protection: | IP20 |
| Mass: | approx. 150 g |
| Dimensions: | 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 inch) |
| Mounting: | on Termination Board |
| Coding: | pin 1 and 4 trimmed For further information see system description. |
| EU-type examination certificate: | EXA 17 ATEX 0040 X |
| Electromagnetic compatibility: Marking: | II 3(1)G Ex nC ec [ia Ga] IIC T4 Gc II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
| Electromagnetic compatibility: Output: | Ex ia |
| Electromagnetic compatibility: Voltage: | 26 V |
| Electromagnetic compatibility: Current: | 110 mA |
| Electromagnetic compatibility: Power: | 715 mW |
| Supply: Maximum safe voltage: | 60 V (Attention! The rated voltage can be lower.) |
| Input: Maximum safe voltage: | 60 V (Attention! The rated voltage can be lower.) |
| Galvanic isolation: Input/Output: | safe electrical isolation acc. to IEC/EN 60079-11, rated insulation voltage 300 Vrms |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-7:2015 , EN 60079-11:2012 , EN 60079-15:2010 |
| UL approval: | E106378 |
| Directive conformity: Control drawing: | 116-0447 (cULus) |
| IECEx approval: IECEx certificate: | IECEx EXA 17.0009X |
| IECEx approval: IECEx marking: | Ex nC ec [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
Logistic parameters
| ECCN: | |
| Country of Origin: | Singapur |
| EAN: | 4050143063505 |
| Weight: | 0.13 kg |
| Length: | 0.00 m |
| Width: | 0.00 m |
| Height: | 0.00 m |