Pepperl+Fuchs
211968
HiDMux2700
Pepperl+Fuchs 211968
HiDMux2700
HART-Multiplexer-Master HiDMux2700
Description
The HART Multiplexer Master provides 32 signal channels for connection to SMART transmitters or control devices supporting digital communication according to the HART standard. Full three-port isolation is included and each input channel has dual capacitor isolation for freedom of loop connection. Each HART Multiplexer Master is networked simply by connecting the high-speed RS 485 output in a multidrop configuration. The device interrogates each field device, under the supervision of the workstation, retrieving information for storage in its internal database, which is then easily accessed. This module is intended to mount on an HiD Termination Board or HART Communcation Board. Also special boards for DCS integration are available. For additional information, refer to the manual and www.pepperl-fuchs.com.
Technical parameters
| Safety Integrity Level (SIL): | SIL 3 |
| Connection: | SL1: 1a, 1b(-); 2a, 2b(+) |
| Rated voltage: | 20.4 ... 30 V DC via Termination Board |
| Rated current: | 28 mA at 24 V , RS-485, quiescent current |
| Power dissipation: | 0.7 W at 24 V |
| Number of channels: | 32 |
| Conformity: | HART field device input (revision 5 to 7) |
| Signal range: | 0.12 Vpp < signal < 1.5 Vpp |
| Leakage current: | < 3 µA at -20 ... 85 °C (-4 ... 185 °F) |
| Terminating resistor: | external 230 ... 500 Ω standard (up to 1000 Ω possible) |
| Output voltage: | ≥ 400 mV ss (with the terminator resistance specified above) |
| Output resistance: | 100 Ω or smaller, capacitive coupling |
| DC isolation: | dual capacitor each channel |
| Common mode voltage: | up to 30 V |
| Input impedance: | > 5 kΩ , according to HART specification |
| Input voltage range: | 0.12 ... 1.5 V ss |
| Common mode voltage: | max. 30 V |
| Differential mode clamping: | ± 5.2 V , for transient or AC signals |
| Common mode clamping: | ± 10 V , for transient or AC signals |
| Carrier detect level: | signal > 0.12 Vpp, carrier detection activated signal < 0.08 Vpp, carrier detection not activated |
| Transmit amplitude: | 200 Ω load, 0.43 Vpp < signal < 0.49 Vpp 500 Ω load, 1.1 Vpp < signal < 1.2 Vpp |
| Device type: | DC isolated bus device |
| Impedance: | high impedance |
| Data link type: | HART primary and secondary |
| Field multi point support: | option available upon request |
| Transfer rate: | 9600 MBit/s, 19200 MBit/s or 38400 MBit/s, selectable via switch |
| Address: | 1 ... 31 , adjustable via DIP switch |
| Type: | RS-485 , differential pair and grounding |
| Topology: | multi point, master/slave connection |
| Interface/power supply: | 500 Vrms |
| Interface/field channels: | 1000 Veff |
| Power supply/field channels: | 1000 Veff |
| Display elements: | LEDs LED PWR ON (power supply), one green LED LED HART TX (HART transmission), one yellow LED LED FAULT (lead fault), one red LED |
| Control elements: | DIP switches at the housing side for: - unit slave address - baud rate - test mode on/off |
| Configuration: | via DIP switches |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2012 For further information see system description. |
| Degree of protection: | IEC 60529:2001 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Relative humidity: | 5 ... 95 %, noncondensing |
| Degree of protection: | IP20 |
| Mass: | approx. 140 g |
| Dimensions: | 18 x 106 x 128 mm (0.7 x 4.2 x 5 inch) |
| Mounting: | on Termination Board |
| Certificate: | CML 17 ATEX 3337 X |
| Electromagnetic compatibility: Marking: | II 3G Ex ec IIC T4 Gc |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-7:2015 |
| CSA approval: CSA certificate: | 1256050 |
| CSA approval: Approved for: | Class I, Division 2, Groups A, B, C, D and non-explosion hazardous area |
| IECEx approval: IECEx certificate: | IECEx CML 17.0178X |
| IECEx approval: IECEx marking: | Ex ec IIC T4 Gc |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
Logistic parameters
| ECCN: | |
| Country of Origin: | SG |
| EAN: | |
| Weight: | 0.00 kg |
| Length: | 0.00 m |
| Width: | 0.00 m |
| Height: | 0.00 m |