Pepperl+Fuchs
194658
EI-0D2-10Y-10B
Pepperl+Fuchs 194658
EI-0D2-10Y-10B
Intrinsically safe Ethernet Isolator
Description
The Ethernet Isolator is an intrinsically safe isolated barrier. It enables cost effective and simple installation in hazardous areas up to Zone 0. It supports high-speed Ethernet and can be mounted in Zone 2. Galvanic Isolation I.S. to non-I.S. Port, 10/100 MBit/s according to IEEE 802.3/.3u, Installation in Zone 2, Ethernet in Zone 1 or Zone 0, Standard Ethernet patch or crossover cable, DIN-Rail mounted and OEM Versionpa. At each end of the trunk, an Ethernet Isolator is installed. In combination, they provide the intrinsically safe energy limitation. The Ethernet Isolator offers a wire-based alternative to wireless LAN, fiber optic solutions, and Ex e installations. In safe area applications, a single Ethernet Isolator can be used for galvanic isolation. The Ethernet Isolator is compatible with all IEEE standards. It provides high noise immunity and low heat dissipation in a compact housing.
Technical parameters
| Rated voltage: | 19.2 ... 35 V DC |
| Rated current: | 150 ... 100 mA |
| Power dissipation: | 3 W |
| Intrinsically safe port: | 10 BASE-T/100 BASE-TX |
| Non-intrinsically safe port: | 10 BASE-T/100 BASE-TX |
| Connection type: | 2 x RJ-45 , IEC 60603-7 |
| Connector pinout: | socket ; TIA/EIA-568-B |
| Transfer rate: | 10/100 Mbit/s , Auto-Negotiation |
| Operating mode: | Half/Full Duplex |
| Cable type: | CAT5e S/FTP AWG 24, Installation cable, L/R ratio max. 10 µH/Ω of all strand combinations |
| I.S. cable length: | typ. 100 m/20 °C |
| Total cable length: | typ. 200 m/20 °C |
| Number of isolators: | max. 2 in series connection |
| LED PWR: | green: Power on |
| LED ACT: | yellow: communication active |
| LED 10/100: | yellow ON: Transfer rate 100 MBit/s , OFF: 10 MBit/s |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 |
| Galvanic isolation: | EN 50020 |
| Degree of protection: | IEC 60529 |
| Climatic conditions: | DIN IEC 721 |
| Shock resistance: | EN 60068-2-27 |
| Vibration resistance: | EN 60068-2-6 |
| Ethernet: | IEEE 802.3 , IEEE 802.3u |
| Ambient temperature: | -40 ... 60 °C (-40 ... 140 °F) |
| Storage temperature: | -40 ... 85 °C (-40 ... 185 °F) |
| Relative humidity: | ≤ 95 % non-condensing |
| Shock resistance: | 15 g 11 ms |
| Vibration resistance: | 1 g 10 ... 150 Hz |
| Pollution degree: | max. 2, according to IEC 60664 |
| Connection type: | Terminals |
| Core cross-section: | up to 2.5 mm2 |
| Housing material: | Polyamide PA 66 |
| Degree of protection: | IP20 according to EN 60529 |
| Mass: | 195 g |
| Mounting: | DIN rail mounting |
| EU-Type Examination Certificate: | PTB 07 ATEX 2025 X |
| Electromagnetic compatibility: Marking: | II (1) G [Ex ia Ga] IIB , II (1) D [Ex ia Da] IIIC , II 3(1)G Ex nA [ia Ga] IIB T4 Gc II 3 (1D) G Ex nA [ia IIIC Da] IIB T4 Gc I (M1) [Ex ia Ma] I |
| Supply: Maximum safe voltage: | 253 V AC |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012 , EN 60079-11:2012 , EN 60079-15:2010 |
| CSA approval: | CSA 15.70016295 |
| Directive conformity: Control drawing: | 116-B032 |
| Directive conformity: Approved for: | Class I, Zone 2, AEx/Ex nA [ia Ga] IIB T4 Gc Class I, Zone 2, AEx/Ex nA [ia Da IIIC] IIB T4 Gc |
| IECEx approval: | IECEx PTB 09.0053X |
| Directive conformity: Approved for: | [Ex ia Ga] IIB [Ex ia Da] IIIC Ex nA [ia Ga] IIB T4 Gc Ex nA [ia IIIC Da] IIB T4 Gc [Ex ia Ma] I |
| Patents: | This product may be covered by the following patent: US7,687,791 |
Logistic parameters
| ECCN: | |
| Country of Origin: | DE |
| EAN: | |
| Weight: | 0.00 kg |
| Length: | 0.00 m |
| Width: | 0.00 m |
| Height: | 0.00 m |