View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Select language
1-Click Quote Request
Product
Pepperl+Fuchs
302488
FB2213BR
Request a Quote
Pepperl+Fuchs 302488
FB2213BR
Digital Output with Position Feedback
On Request. Please send us an email to inquire the price and avaliability.
"ucnguBrctvdgcxgt0eqo"
Description
The digital output features 1 output with 2 feedback inputs. 1 digital output, 2 digital inputs, Inputs and output Ex ia, Installation in suitable enclosures in Zone 1, Module can be exchanged under voltage (hot swap)pa. The device can be used to switch solenoids, sounders, or indicators (without line fault detection) in the field. Furthermore, the device accepts digital input signals of NAMUR sensors or mechanical contacts from the field. Open and short-circuit line faults are detected. The intrinsically safe inputs and the output are galvanically isolated from the bus and the power supply.
Technical parameters
| Occupied slots: | 1 |
| Connection: | backplane bus |
| Rated voltage: | 12 V DC , only in connection with the power supplies FB92** |
| Power dissipation: | 1.5 W |
| Power consumption: | 1.5 W |
| Connection: | backplane bus |
| Interface: | manufacturer-specific bus to standard com unit |
| Number of channels: | 2 |
| Sensor interface: Connection: | NAMUR sensor |
| Sensor interface: Connection [2]: | volt-free contact |
| Sensor interface: Connection [3]: | active binary signal 24 V DC |
| Connection: | channel I: 2+, 5-; channel II: 3+, 6- |
| Rated values: | acc. to EN 60947-5-6 (NAMUR) |
| Switching point/switching hysteresis: | 1.2 ... 2.1 mA / ± 0.2 mA |
| Internal resistor: | 1 kΩ |
| Line fault detection: | can be switched on/off for each channel via configuration tool |
| Sensor interface: Connection: | mechanical switch with additional resistors (see connection diagram) proximity switches without additional wiring |
| Sensor interface: Short-circuit: | < 360 Ω |
| Sensor interface: Open-circuit: | < 0.35 mA |
| Minimum pulse duration: | 1 ms |
| Number of channels: | 1 |
| Suitable field devices: Field device: | Solenoid Valve |
| Suitable field devices: Field device [2]: | audible alarm |
| Suitable field devices: Field device [3]: | visual alarm |
| Connection: | channel I: 1+, 4- |
| Open loop voltage: | 26.7 V |
| Current limit: | 40 mA |
| Internal resistor: | 509 Ω |
| Line fault detection: | can be switched on/off for each channel via configuration tool , also when turned off (every 2.5 s the valve is turned on for 2 ms) |
| Suitable field devices: Short-circuit: | < 200 Ω |
| Suitable field devices: Open-circuit: | > 6 kΩ |
| Response time: | 20 ms (depending on bus cycle time) |
| Watchdog: | within 0.5 s the device goes in safe state, e.g. after loss of communication |
| LED indication: | LED green: supply LED red: output line fault LED yellow: status output |
| Coding: | optional mechanical coding via front socket |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1 |
| Electromagnetic compatibility: | NE 21 |
| Degree of protection: | IEC 60529 |
| Environmental test: | EN 60068-2-14 |
| Shock resistance: | EN 60068-2-27 |
| Vibration resistance: | EN 60068-2-6 |
| Damaging gas: | EN 60068-2-42 |
| Relative humidity: | EN 60068-2-56 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Storage temperature: | -25 ... 85 °C (-13 ... 185 °F) |
| Relative humidity: | 95 % non-condensing |
| Shock resistance: | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 |
| Vibration resistance: | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
| Damaging gas: | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 |
| Degree of protection: | IP20 (module) , a separate housing is required acc. to the system description |
| Connection: | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
| Mass: | approx. 350 g |
| Dimensions: | 28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch) |
| EU-Type Examination Certificate: | PTB 97 ATEX 1074 U |
| Electromagnetic compatibility: Marking: | II 2(1) G Ex d [ia Ga] IIC Gb |
| Input: Voltage: | 14.1 V |
| Input: Current: | 16 mA |
| Input: Power: | 55 mW (linear characteristic) |
| Input: Internal capacitance: | 1.65 nF |
| Output: Voltage: | 28.7 V |
| Output: Current: | 68 mA |
| Output: Power: | 485 mW |
| Output: Internal capacitance: | 1.65 nF |
| Galvanic isolation: Input/power supply, internal bus: | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V |
| Galvanic isolation: Output/power supply, internal bus: | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2009 EN 60079-1:2007 EN 60079-11:2007 EN 60079-26:2007 EN 61241-11:2006 |
| ATEX approval: | PTB 97 ATEX 1075 ; PTB 97 ATEX 1074 U |
| EAC approval: | Russia: RU C-IT.MIII06.B.00129 |
| Marine approval: Lloyd Register: | 15/20021 |
| Marine approval: DNV GL Marine: | TAA0000034 |
| Marine approval: American Bureau of Shipping: | T1450280/UN |
| Marine approval: Bureau Veritas Marine: | 22449/B0 BV |
| System information: | The module has to be mounted in appropriate backplanes and housings (FB92**) in Zone 1, 2, 21, 22 or outside hazardous areas (gas or dust). Here, observe the corresponding EC-type examination certificate. |
| Supplementary information: | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |
Logistic parameters
| ECCN: | |
| Country of Origin: | DE |
| EAN: | |
| Weight: | 0.00 kg |
| Length: | 0.00 m |
| Width: | 0.00 m |
| Height: | 0.00 m |