Pepperl+Fuchs
295670-100261
OMT300-R200-IEP-IO-V1
Pepperl+Fuchs 295670-100261
OMT300-R200-IEP-IO-V1
Distance sensor
Description
The optical sensors in the series are the first devices to offer an end-to-end solution in a medium-sized standard design – from the thru-beam sensor through to the measuring distance sensor. As a result of this design, the sensors are able to perform practically all standard automation tasks. Distance sensor, Medium design with versatile mounting options, Space-saving distance sensors in small standardized design, Multi Pixel Technology (MPT) - exact and precise signal evaluation, IO-link interface for service and process data, Analog output 4 .. 20 mAfa. The entire series enables sensors to communicate via IO-Link. The DuraBeam laser sensors are durable and can be used in the same way as a standard sensor. Multi Pixel Technology (MPT) ensures that the standard sensors are flexible and can be adapted to the application environment.
Technical parameters
| Measurement range: | 100 ... 300 mm |
| Reference target: | standard white, 100 mm x 100 mm |
| Light source: | LED |
| Light type: | modulated visible red light |
| LED risk group labelling: | exempt group |
| Angle deviation: | max. +/- 1.5 ° |
| Diameter of the light spot: | approx. 8 mm at a distance of 300 mm |
| Angle of divergence: | 1.8 ° |
| Ambient light limit: | EN 60947-5-2 : 45000 Lux |
| Resolution: | 0.1 mm |
| MTTFd: | 520 a |
| Mission Time (TM): | 20 a |
| Diagnostic Coverage (DC): | 0 % |
| Operation indicator: | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Function indicator: | LED yellow: constantly on - switch output active constantly off - switch output inactive |
| Control elements: | Teach-In key |
| Control elements: | 5-step rotary switch for operating modes selection |
| Operating voltage: | 18 ... 30 V DC |
| Ripple: | max. 10 % |
| No-load supply current: | < 25 mA at 24 V supply voltage |
| Protection class: | III |
| Interface type: | IO-Link ( via C/Q = pin 4 ) |
| Device profile: | Identification and diagnosis Smart Sensor type 0/type 3.3 |
| Transfer rate: | COM 2 (38.4 kBaud) |
| IO-Link Revision: | 1.1 |
| Min. cycle time: | 3 ms |
| Process data width: | Process data input 4 byte Process data output 2 bits |
| SIO mode support: | yes |
| Device ID: | 0x111905 (1120517) |
| Compatible master port type: | A |
| Switching type: | The default setting is: C/Q - Pin4: NPN normally open, PNP normally closed, IO-Link I—Pin2: analog output 4...20 mA |
| Signal output: | 1 push-pull output , 1 analog output , short-circuit-proof, reverse polarity protection, surge-proof |
| Switching voltage: | max. 30 V DC |
| Switching current: | max. 100 mA , resistive load |
| Usage category: | DC-12 and DC-13 |
| Voltage drop: | ≤ 1.5 V DC |
| Response time: | 2 ms , see table 1 |
| Output type: | 1 current output: 4 ... 20 mA |
| Load resistor: | > 1 kΩ voltage output ; ≤ 470 Ω current output |
| : Recovery time: | 2 ms |
| Communication interface: | IEC 61131-9 |
| Product standard: | EN 60947-5-2 |
| Temperature drift: | 0.05 %/K |
| Warm up time: | 5 min |
| Repeat accuracy: | < 0.5 % , see table 1 |
| Linearity error: | 0.5 % |
| UL approval: | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| CCC approval: | CCC approval / marking not required for products rated ≤36 V |
| Ambient temperature: | 10 ... 50 °C (50 ... 122 °F) |
| Storage temperature: | -40 ... 70 °C (-40 ... 158 °F) |
| Housing width: | 15 mm |
| Housing height: | 50.6 mm |
| Housing depth: | 41.7 mm |
| Degree of protection: | IP67 / IP69 / IP69K |
| Connection: | 4-pin, M12 x 1 connector, 90° rotatable |
| Material: Housing: | PC (Polycarbonate) |
| Material: Optical face: | PMMA |
| Mass: | approx. 37 g |
Logistic parameters
| ECCN: | |
| Country of Origin: | SG |
| EAN: | |
| Weight: | 0.00 kg |
| Length: | 0.00 m |
| Width: | 0.00 m |
| Height: | 0.00 m |