View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Seleccione el idioma
Solicitud con 1 clic
Producto
Pepperl+Fuchs
223085
FB7204B3
Solicitar una oferta
Pepperl+Fuchs 223085
FB7204B3
Universal Input/Output (HART)
Bajo pedido. Envíenos un correo electrónico para consultar el precio y la disponibilidad.
"ucnguBrctvdgcxgt0eqo"
Descripción
4-channel, Inputs Ex ia, Outputs Ex ia, Installation in suitable enclosures in Zone 1, Module can be exchanged under voltage (hot swap)pa
Parámetros técnicos
| Occupied slots: | 1 |
| Connection: | backplane bus |
| Rated voltage: | Use only in connection with the power supplies FB92** |
| Power dissipation: | 2 W |
| Power consumption: | 3 W |
| Connection: | backplane bus |
| Interface: | manufacturer-specific bus to standard com unit |
| Number of channels: | 4 |
| Suitable field devices: Field device: | pressure converter |
| Suitable field devices: Field device [2]: | flow converter |
| Suitable field devices: Field device [3]: | level converter |
| Suitable field devices: Field device [4]: | Temperature Converter |
| Field device interface: Connection: | 2-wire transmitter |
| Connection: | terminals 1+, 2-; 3+, 4-; 5+, 6-; 7+, 8- |
| Transmitter supply voltage: | min. 15 V at 20 mA ; 21.5 V at 4 mA |
| Input resistance: | 15 Ω |
| Line fault detection: | can be switched on/off for each channel via configuration tool , configurable via configuration tool |
| Field device interface: Short-circuit: | factory setting: > 21 mA Can be parameterized in the range 0 ... 22 mA |
| Field device interface: Open-circuit: | factory setting: < 3.6 mA Can be parameterized in the range 0 ... 22 mA |
| HART communication: | yes |
| HART secondary variable: | yes |
| Number of channels: | 4 |
| Suitable field devices: Field device: | Proportional Valve |
| Suitable field devices: Field device [2]: | I/P converters |
| Suitable field devices: Field device [3]: | on-site display |
| Connection: | terminals 1+, 2-; 3+, 4-; 5+, 6-; 7+, 8- |
| Current: | 0 ... 20 mA short-circuit protected |
| Line fault detection: | can be switched on/off for each channel via configuration tool , configurable via configuration tool |
| Suitable field devices: Short-circuit: | factory setting: < 50 Ω configurable between 0 ... 26 mA |
| Suitable field devices: Open-circuit: | deviation of preset output value > 0.5 mA |
| Load: | max. 750 Ω at 20 mA |
| HART communication: | yes |
| HART secondary variable: | yes |
| Watchdog: | output off 0.5 s after serious fault |
| Number of channels: | 4 |
| Sensor interface: Connection [2]: | volt-free contact |
| Connection: | terminals 1+, 2-; 3+, 4-; 5+, 6-; 7+, 8- |
| Line fault detection: | can be switched on/off for each channel via configuration tool |
| Sensor interface: Connection: | mechanical switch with additional resistors (see connection diagram) |
| Sensor interface: Short-circuit: | > 7 mA |
| Sensor interface: Open-circuit: | < 0.1 mA |
| Digital signals (active): Switching point: ON: | > 2.1 mA |
| Digital signals (active): Switching point: OFF: | < 1.2 mA |
| Number of channels: | 4 |
| Suitable field devices: Field device: | Solenoid Valve |
| Suitable field devices: Field device [2]: | audible alarm |
| Suitable field devices: Field device [3]: | visual alarm |
| Connection: | terminals 1+, 2-, 3+, 4-, 5+, 6-, 7+, 8- |
| Drive capability: | 12 V / 22 mA |
| Open loop voltage: | min. 22.7 V |
| Current limit: | 22 mA |
| Internal resistor: | 385 Ω |
| Line fault detection: | can be switched on/off for each channel via configuration tool |
| Suitable field devices: Test current: | 0.4 mA |
| Suitable field devices: Short-circuit: | < 50 Ω |
| Suitable field devices: Open-circuit: | < 0.2 mA |
| Deviation: After calibration: | 0.1 % of the signal range at 20 °C (68 °F) |
| Deviation: Influence of ambient temperature: | 0.1 %/10 K of the signal range |
| Resolution: | 12 Bit (0 ... 26 mA) |
| Refresh time: | approx. 100 ms (4 channels) |
| LED indication: | Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Configuration LED (AI, AO, DI, DO) white: selected channel mode |
| Coding: | optional mechanical coding via front socket |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1 |
| Electromagnetic compatibility: | NE 21 |
| Degree of protection: | IEC 60529 |
| Environmental test: | EN 60068-2-14 |
| Shock resistance: | EN 60068-2-27 |
| Vibration resistance: | EN 60068-2-6 |
| Damaging gas: | EN 60068-2-42 |
| Relative humidity: | EN 60068-2-56 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Storage temperature: | -25 ... 85 °C (-13 ... 185 °F) |
| Relative humidity: | 95 % non-condensing |
| Shock resistance: | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 |
| Vibration resistance: | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ± 1 mm/0.7 g; 90 minutes at each resonance |
| Damaging gas: | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 |
| Degree of protection: | IP20 (module) , a separate housing is required acc. to the system description |
| Connection: | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
| Mass: | approx. 425 g |
| Dimensions: | 28 x 107 x 132 mm (1.1 x 4.2 x 5.2 inch) |
| EU-type examination certificate: | Presafe 19 ATEX 14057U |
| Electromagnetic compatibility: Marking: | II 2(1)G Ex db eb q [ia Ga] IIC Gb II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
| Supply: Voltage: | 27 V |
| Supply: Current: | 87 mA |
| Supply: Power: | 575 mW (linear characteristic) |
| Input: | Ex ia |
| Supply: Voltage: | 27 V |
| Supply: Current: | 87 mA |
| Supply: Power: | 575 mW (linear characteristic) |
| Supply: Internal capacitance: | 0 nF |
| Supply: Internal inductance: | 0 mH |
| Output: | Ex ia |
| Supply: Voltage: | 27 V |
| Supply: Current: | 87 mA |
| Supply: Power: | 575 mW (linear characteristic) |
| Galvanic isolation: Rated voltage: | 250 V field circuits to control and supply circuits |
| Galvanic isolation: Input/power supply, internal bus: | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V |
| Galvanic isolation: Output/power supply, internal bus: | safe electrical isolation acc. to EN 60079-11, voltage peak value 375 V |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 EN 60079-1:2014 EN 60079-5:2015 EN 60079-7:2015 EN 60079-11:2012 |
| ATEX approval: | Presafe 19 ATEX 14057U |
| IECEx approval: | IECEx PRE 19.0012U |
| Directive conformity: Approved for: | Ex db eb q [ia Ga] IIC Gb [Ex ia Da] IIIC [Ex ia Ma] I |
| System information: | The module has to be mounted in appropriate backplanes and housings (FB92**) in Zone 1, 2, 21, 22 or outside hazardous areas (gas or dust). Here, observe the corresponding EC-type examination certificate. |
| Supplementary information: | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |
Parámetros logísticos
| ECCN: | |
| País de origen: | DE |
| EAN: | |
| Peso: | 0,00 kg |
| Longitud: | 0,00 m |
| Anchura: | 0,00 m |
| Altura: | 0,00 m |