View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Выберите язык
Запрос цены в 1 клик
Продукт
Pepperl+Fuchs
192334
KFU8-UFT-2.D.FA
Сделать запрос
Pepperl+Fuchs 192334
KFU8-UFT-2.D.FA
Frequency Converter with Direction and Synchronization Monitor
По запросу. Пожалуйста, отправьте нам письмо, чтобы узнать цену и наличие.
"ucnguBrctvdgcxgt0eqo"
Описание
This signal conditioner analyzes 2 digital signals (NAMUR sensor/mechanical contact) and functions as a rotation direction indicator, slip monitor, frequency monitor or synchronization monitor. 2-channel signal conditioner, Universal usage at different power supplies, Dry contact or NAMUR inputs, Input frequency 1 mHz .. 1 kHz, Current output 0/4 mA ... 20 mA, Relay contact and transistor output, Start-up override, Configurable by PACTware or keypad, Line fault detection (LFD), Rated voltage: 20 .. 90 V DC / 48 .. 253 V AC 50 .. 60 Hzpa. Each proximity sensor or switch controls a passive transistor output. The 2 relay outputs indicate if the input signal is above or below the trip value or the rotational direction. The analog output can be programmed to be proportional to the input frequency or slip differential. The unit is easily programmed by the use of a keypad located on the front of the unit or with the PACTware™ configuration software. Line fault detection of the field current is indicated by a red LED. For additional information, refer to the manual and www.pepperl-fuchs.com.
Технические характеристики
| Signal type: | Digital Input |
| Connection: | terminals 23, 24 |
| Rated voltage: | 20 ... 90 V DC / 48 ... 253 V AC 50 ... 60 Hz |
| Rated current: | approx. 130 mA |
| Power dissipation: | 2.2 W / 3.5 VA |
| Power consumption: | 2.5 W / 4 VA |
| Programming interface: | programming socket |
| Connection side: | field side |
| Connection: | input I: terminals 1+, 3- input II: terminals 4+, 6- input III: terminals 13+, 14- (control input 1) input IV: terminals 15+, 14- (control input 2) |
| Input I, II: | 2-wire sensor, sensor acc. to EN 60947-5-6 (NAMUR) or mechanical contact |
| : Open circuit voltage/short-circuit current: | 8.2 V / 10 mA |
| : Switching point/switching hysteresis: | logic 1: > 2.5 mA ; logic 0: < 1.9 mA |
| : Pulse duration: | min. 250 µs , overlap on direction of rotation signal: ≥ 125 µs |
| : Input frequency: | rotation direction monitoring 0.001 ... 1000 Hz slip monitoring 10 ... 1000 Hz |
| : Line fault detection: | breakage I ≤ 0.15 mA; short-circuit I > 4 mA |
| Input III, IV: Active/Passive: | I > 4 mA (for min. 100 ms) / I < 1.5 mA |
| Input III, IV: Open circuit voltage/short-circuit current: | 18 V / 5 mA |
| Connection side: | control side |
| Connection: | output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 19+, 20- output IV: terminals 21+, 20- output V: terminals 7-, 8+ |
| Output I, II: | signal, relay |
| Input III, IV: Contact loading: | 250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A |
| Input III, IV: Mechanical life: | 5 x 107 switching cycles |
| Input III, IV: Energized/De-energized delay: | approx. 20 ms / approx. 20 ms |
| Output III and IV: | signal , electronic output, passive |
| Input III, IV: Contact loading: | 40 V DC |
| Input III, IV: Signal level: | 1-signal: (L+) -2.5 V (50 mA, short-circuit/overload proof) 0-signal: blocked output (off-state current ≤ 10 µA) |
| Output V: | analog |
| Input III, IV: Current range: | 0 ... 20 mA or 4 ... 20 mA |
| Input III, IV: Open loop voltage: | max. 24 V DC |
| Input III, IV: Load: | max. 650 Ω |
| Input III, IV: Fault signal: | downscale I ≤ 3.6 mA, upscale I ≥ 21.5 mA (acc. NAMUR NE43) |
| Programming interface: Connection: | programming socket |
| Programming interface: Interface: | RS 232 |
| Input I and II: Measurement range: | 0.001 ... 1000 Hz |
| Input I and II: Resolution: | slip monitoring: 1% frequency measurement: 0,1% of measured value; but >0.001Hz |
| Input I and II: Accuracy: | slip monitoring: 1% frequency measurement: 0.5% of measured value; but >0.001Hz |
| Input I and II: Measuring time: | frequency measurement: < 100 ms |
| Input I and II: Influence of ambient temperature: | 0.003 %/K (30 ppm) |
| Output I, II: Response delay: | ≤ 200 ms |
| Output V: Resolution: | < 10 µA |
| Output V: Accuracy: | < 30 µA |
| Output V: Influence of ambient temperature: | 0.005 %/K (50 ppm) |
| Input I, II/other circuits: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Input III, IV/power supply: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output I, II/other circuits: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Mutual output I, II, III: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Mutual output I, II, IV: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output III, IV/power supply: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output III, IV/input III, IV: | basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 Veff |
| Output III, IV/V: | basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 Veff |
| Output V/power supply: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Interface/power supply: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Interface/output III, IV: | basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 Veff |
| Display elements: | LEDs , display |
| Control elements: | Control panel |
| Configuration: | via operating buttons via PACTware |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2006 |
| Low voltage: Directive 2014/35/EU: | EN 61010-1:2010 |
| Electromagnetic compatibility: | NE 21:2006 |
| Degree of protection: | IEC 60529:2001 |
| Input: | EN 60947-5-6:2000 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Connection: | screw terminals |
| Mass: | 300 g |
| Dimensions: | 40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) , housing type C3 |
| Mounting: | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
Логистические характеристики
| ТН ВЭД: | |
| Страна происхождения: | SG |
| EAN: | |
| Вес: | 0,00 kg |
| Длина: | 0,00 m |
| Ширина: | 0,00 m |
| Высота: | 0,00 m |