View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Seleccione el idioma
Solicitud con 1 clic
Producto
Pepperl+Fuchs
281885
VBG-EC-K30-DMD-S32-EV
Solicitar una oferta
Pepperl+Fuchs 281885
VBG-EC-K30-DMD-S32-EV
AS-Interface Gateway/Safety Monitor
Bajo pedido. Envíenos un correo electrónico para consultar el precio y la disponibilidad.
"ucnguBrctvdgcxgt0eqo"
Descripción
EtherCat gateway with integrated safety monitor, double master for 2 AS-Interface networks, power supply input with decoupling coilsfa
Parámetros técnicos
| AS-Interface specification: | V3.0 |
| PLC-Functionality: | activateable |
| Duplicate address detection: | from AS-Interface slaves |
| Earth fault detection: | integrated |
| EMC monitoring: | integrated |
| Diagnostics function: | Extended function via display |
| Data decoupling: | integrated |
| Switch-on delay: | < 10 s |
| Response delay: | < 40 ms |
| UL File Number: | E223772 only from low voltage, limited energy source (SELV or PELV) or listed Class 2 source |
| Safety Integrity Level (SIL): | SIL 3 |
| Performance level (PL): | PL e |
| MTTFd: | 100 a |
| B10d: | 2.5 E+5 |
| Display: | Illuminated graphical LC display for addressing and error messages |
| LED ETHERNET: | EtherCAT active; LED green |
| LED AS-i ACTIVE: | AS-Interface operation normal; LED green |
| LED CONFIG ERR: | configuration error; LED red |
| LED PRG ENABLE: | autom. programming; LED green |
| LED POWER: | voltage ON; LED green |
| LED PRJ MODE: | projecting mode active; LED yellow |
| LED U AS-i: | AS-Interface voltage; LED green |
| LED AUX: | ext. auxiliary voltage UAUX ; LED green |
| LED IN: | 6 x LED green |
| LED OUT: | Output circuit closed; 6 x green LEDs |
| Button: | 4 |
| Switch SET: | Selection and setting of a slave address |
| OK button: | Mode selection traditional-graphical/confirmation |
| Button MODE: | Mode selection PRJ-operation/save configuration/cursor |
| ESC button: | Mode selection traditional-graphical/cancel |
| Insulation voltage: | ≥ 500 V |
| Rated operating voltage: | 26.5 ... 31.6 V from AS-Interface; 24 V DC |
| Rated operating current: | approx. 300 mA PELV |
| Interface type: | RJ-45 |
| Physical: | 2 x RJ-45 |
| Protocol: | EtherCAT acc. to IEEE 802.3 |
| Transfer rate: | 10 MBit/s / 100 MBit/s , Automatic baud rate detection |
| Interface type: | RJ-45 Ethernet Diagnostic Interface |
| Transfer rate: | 10 MBit/s |
| Interface type: | Chip card slot |
| Number/Type: | 6 inputs Safety: 3 x 2 channels Or 6 standard inputs |
| Safety output: | 6 semiconductor outputs Output circuits: 6 PNP transistor outputs Max. contact load: 1.2 ADC-13 at 30 VDC, Σ = 7.2 A in total (see derating) |
| Ethernet: | RJ-45 |
| AS-Interface: | spring terminals, removable |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 62026-2:2013 EN 61000-6-2/AC:2005, EN 61000-6-4:2007+A1:2011 |
| Machinery Directive: Directive 2006/42/EC: | EN 61508:2010 EN ISO 13849-1/AC:2009 EN 62061:2005+A1:2013 |
| Degree of protection: | EN 60529:2000 |
| Emitted interference: | EN 61000-6-4:2007/A1:2011 |
| AS-Interface: | EN 62026-2:2013 |
| Noise immunity: | EN 61000-6-2/AC:2005 |
| Shock resistance: | EN 61131-2:2004 |
| Functional safety: | EN ISO 13849-1:2008/AC:2009, EN ISO 13849-2:2012 (up to PL e), EN 61508:2010 and EN 62061:2005+A1:2013 (up to SIL3) |
| UL approval: | An isolated source with a secondary open circuit voltage of ≤ 30 VDC with a 3 A maximum over current protection. Over current protection is not required when a Class 2 source is employed. UL mark does not provide UL certification for any functional safety rating or aspects of the device. |
| Ambient temperature: | 0 ... 55 °C (32 ... 131 °F) |
| Storage temperature: | -25 ... 85 °C (-13 ... 185 °F) |
| Degree of protection: | IP20 |
| Material: Housing: | Stainless steel |
| Mass: | 800 g |
| Construction type: | Low profile housing |
Parámetros logísticos
| ECCN: | |
| País de origen: | DE |
| EAN: | |
| Peso: | 0,90 kg |
| Longitud: | 0,00 m |
| Anchura: | 0,00 m |
| Altura: | 0,00 m |