Pepperl+Fuchs
261918
KFD2-HLC-Ex1.D.2W
Pepperl+Fuchs 261918
KFD2-HLC-Ex1.D.2W
HART Loop Converter
Описание
This isolated barrier is used for intrinsic safety applications. It is a HART loop converter that provides power to transmitters or can be connected to existing HART loops in parallel. 1-channel isolated barrier, 24 V DC supply (Power Rail), HART field device input with transmitter power supply, Usable as signal splitter (1 input and several outputs), 2 relay contact outputs (change-over contacts), 3 analog outputs 4 mA .. 20 mA, Sink and source mode output, Configurable by keypadpa. It is able to evaluate up to four HART variables (PV, SV, TV, QV). Of those four HART variables, the data contained in any three of them can be converted to three different 4 mA .. 20 mA current signals. These loop signals can be connected to display devices or analog inputs on the process control system/ control system. In addition to the current outputs, two form C changeover relay contacts are available and can be programmed to operate at trip values from the HART variables. The unit is easily programmed by the use of a keypad located on the front of the unit or with the PACTware™ configuration software. For additional information, refer to the manual and www.pepperl-fuchs.com.
Технические характеристики
| Signal type: | Analog input |
| Connection: | Power Rail or terminals 23+, 24- |
| Rated voltage: | 19 ... 30 V DC |
| Rated current: | approx. 130 mA at 24 V DC |
| Power dissipation: | 2.5 W |
| Power consumption: | 3.1 W |
| Conformity: | HART field device input (revision 5 to 7) |
| Programming interface: | programming socket |
| Connection side: | field side |
| Connection: | terminals 1, 2, 3, 4, 5, 6 |
| Open circuit voltage/short-circuit current: | typ. 24 V / 28 mA |
| Input resistance: | 250 Ω , 5 % (terminals 2, 3 and with jumper on 5, 6) |
| Available voltage: | ≥ 15.5 V at 20 mA, short-circuit protected |
| Connection side: | control side |
| Connection: | output I: terminals 10, 11, 12, output II: terminals 16, 17, 18 output III: terminals 7, 8, 9, output IV: terminals 13, 14, 15, output V: terminals 19, 20, 21 |
| Output I, II: Output signal: | relay and LED yellow |
| Output I, II: Mechanical life: | 107 switching cycles |
| Output I, II: Energized/De-energized delay: | approx. 20 ms / approx. 20 ms |
| Output III, IV, V: Output signal: | analog |
| Output III, IV, V: Current range: | 4 ... 20 mA , (source or sink mode) |
| Output III, IV, V: Load: | max. 650 Ω , source mode |
| Output III, IV, V: Voltage range: | 5 ... 30 V , sink mode from external supply |
| Output III, IV, V: Fault signal: | downscale I ≤ 2 mA, upscale I ≥ 21.5 mA (acc. NAMUR NE43) or hold measurement value |
| Other outputs: | HART communicator on terminals 22, 24 |
| Collective error message: | Power Rail and LED red |
| Output III, IV, V: Resolution: | max. 2 µA |
| Output III, IV, V: Accuracy: | < 20 µA, 10 µA typ. |
| Output III, IV, V: Influence of ambient temperature: | < ± 2 µA/K |
| Output III, IV, V: Duration of measurement/Response delay: | HART message acquisition time plus 100 ms |
| Relay: | programmable either for fault or trip value (with direction, hysteresis and delay) |
| Output I/II: | functional insulation acc. to IEC 62103, rated insulation voltage 250 Veff |
| Output I, II/other circuits: | reinforced insulation acc. to IEC 62103, rated insulation voltage 300 Vrms |
| Output III/IV/V/power supply: | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Display elements: | LEDs , display |
| Control elements: | Control panel |
| Configuration: | via operating buttons via PACTware |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Low voltage: Directive 2014/35/EU: | EN 61010-1:2010 |
| Electromagnetic compatibility: | NE 21:2006 |
| Degree of protection: | IEC 60529:2001 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Connection: | screw terminals |
| Mass: | 300 g |
| Dimensions: | 40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) , housing type C3 |
| Mounting: | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| EU-Type Examination Certificate: | BASEEFA 07 ATEX 0174 |
| Low voltage: Marking: | II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC |
| Supply: Maximum safe voltage: | 253 V AC (Attention! The rated voltage can be lower.) |
| Equipment: | terminals 1, 4/3 (with link between terminals 4 and 5) |
| Supply: Voltage Uo: | 25.2 V |
| Supply: Current Io: | 104.9 mA |
| Supply: Power Po: | 0.661 W |
| Equipment: | terminals 2, 5/3 |
| Supply: Voltage Ui: | < 28 V |
| Supply: Power Pi: | < 1.33 W |
| Supply: Voltage Uo: | 1.1 V |
| Supply: Current Io: | 11.9 mA |
| Supply: Power Po: | 4 mW |
| Output I, II: | terminals 10, 11, 12; 16, 17, 18 , non-intrinsically safe |
| Supply: Maximum safe voltage: | 253 V (Attention! Um is no rated voltage.) |
| Supply: Contact loading: | 253 V AC/1 A/cos φ > 0.7; 30 V DC/1 A resistive load (BASEEFA 07 ATEX 0174) 50 V AC/1 A/cos φ > 0.7; 30 V DC/1 A resistive load (Pepperl+Fuchs self-declaration) |
| Output III, IV, V: | terminals 7, 8, 9; 13, 14, 15; 19, 20, 21 , non-intrinsically safe |
| Supply: Maximum safe voltage: | 253 V (Attention! Um is no rated voltage.) |
| Certificate: | PF 07 CERT 1141 X |
| Supply: Marking: | II 3G Ex nA nC IIC T4 Gc |
| Galvanic isolation: Input/Other circuits: | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| FM approval: Control drawing: | 116-0129 |
| IECEx approval: IECEx certificate: | IECEx BAS 07.0047 |
| IECEx approval: IECEx marking: | [Ex ia Ga] IIC , [Ex ia Da] IIIC |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
| Optional accessories: | - power feed module KFD2-EB2(.R4A.B)(.SP) - universal power rail UPR-03(-M)(-S) - profile rail K-DUCT-BU(-UPR-03) |
Логистические характеристики
| ТН ВЭД: | |
| Страна происхождения: | SG |
| EAN: | |
| Вес: | 0,00 kg |
| Длина: | 0,00 m |
| Ширина: | 0,00 m |
| Высота: | 0,00 m |