View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Выберите язык
Запрос цены в 1 клик
Продукт
Pepperl+Fuchs
255620
KFD2-CRG2-Ex1.D
Сделать запрос
Pepperl+Fuchs 255620
KFD2-CRG2-Ex1.D
Transmitter Power Supply
По запросу. Пожалуйста, отправьте нам письмо, чтобы узнать цену и наличие.
"ucnguBrctvdgcxgt0eqo"
Описание
1-channel isolated barrier, 24 V DC supply (Power Rail), Input 2-wire and 3-wire transmitters and 2-wire current sources, Output 0/4 mA ... 20 mA, 2 relay contact outputs, Adjustable energized/de-energized delay, Programmable high/low alarm, Linearization function (max 20 points), Line fault detection (LFD), Up to SIL 2 acc. to IEC 61508/IEC 61511pa. This isolated barrier is used for intrinsic safety applications. The device supplies 2-wire and 3-wire transmitters, and can also be used with current sources. Two relays and an active 0/4 mA ... 20 mA current source are available as outputs. The relay contacts and the current output can be integrated in security-relevant circuits. The current output is easily scaled. On the display the measured value can be indicated in various physical units. The device is easily configured by the use of keypad or with the PACTware configuration software. The input has a line fault detection. A fault is signalized by LEDs acc. to NAMUR NE44 and a separate collective error message output. For additional information, refer to the manual and www.pepperl-fuchs.com.
Технические характеристики
| Signal type: | Analog input |
| Safety Integrity Level (SIL): | SIL 2 |
| Connection: | Power Rail or terminals 23+, 24- |
| Rated voltage: | 20 ... 30 V DC |
| Rated current: | approx. 130 mA |
| Power dissipation: | 2 W |
| Power consumption: | 2.5 W |
| Programming interface: | programming socket |
| Connection side: | field side |
| Connection: | terminals 1, 2, 3 |
| Input I: Input signal: | 0/4 ... 20 mA |
| Input I: Available voltage: | ≥ 15 V at 20 mA |
| Input I: Open circuit voltage/short-circuit current: | 24 V / 33 mA |
| Input I: Input resistance: | 45 Ω (terminals 2, 3) |
| Input I: Line fault detection: | breakage I < 0.2 mA; short-circuit I > 22 mA |
| Connection side: | control side |
| Connection: | output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 8+, 7- |
| Output signal: | 0 ... 20 mA or 4 ... 20 mA |
| Output I, II: | signal, relay |
| Input I: Contact loading: | 250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A |
| Input I: Mechanical life: | 5 x 107 switching cycles |
| Output III: | Signal, analog |
| Input I: Current range: | 0 ... 20 mA or 4 ... 20 mA |
| Input I: Open loop voltage: | max. 24 V DC |
| Input I: Load: | max. 650 Ω |
| Input I: Fault signal: | downscale I ≤ 3.6 mA, upscale I ≥ 21 mA (acc. NAMUR NE43) |
| Energized/De-energized delay: | 0 ... 250 s , adjustable |
| Input I: Accuracy: | < 30 µA |
| Input I: Influence of ambient temperature: | 0.003 %/K (30 ppm) |
| Output I, II: Response delay: | ≤ 200 ms at bounce from 0 ... 20 mA |
| Output III: Resolution: | ≤ 10 µA |
| Output III: Accuracy: | < 20 µA |
| Output III: Influence of ambient temperature: | 0.005 %/K (50 ppm) |
| Output III: Reaction time: | < 650 ms at bounce from 0 ... 20 mA at the input, 90 % of output full-scale value |
| Input/Other circuits: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output I, II/other circuits: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Mutual output I, II, III: | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output III/power supply and collective error: | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Interface/power supply and collective error: | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Display elements: | LEDs , display |
| Control elements: | Control panel |
| Configuration: | via operating buttons via PACTware |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Low voltage: Directive 2014/35/EU: | EN 61010-1:2010 |
| Electromagnetic compatibility: | NE 21:2006 |
| Degree of protection: | IEC 60529:2001 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Connection: | screw terminals |
| Mass: | 300 g |
| Dimensions: | 40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) , housing type C3 |
| Mounting: | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| EU-Type Examination Certificate: | TÜV 01 ATEX 1701 |
| Low voltage: Marking: | II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
| Low voltage: Input: | Ex ia |
| Supply: Maximum safe voltage: | 40 V DC (Attention! The rated voltage can be lower.) |
| Equipment: | terminals 1+, 3- |
| Supply: Voltage Uo: | 25.8 V |
| Supply: Current Io: | 93 mA |
| Supply: Power Po: | 0.603 W |
| Equipment: | terminals 2-, 3 |
| Supply: Voltage Ui: | < 30 V |
| Supply: Current Ii: | 115 mA |
| Supply: Voltage Uo: | 5 V |
| Supply: Current Io: | 0.3 mA |
| Supply: Power Po: | 0.3 mW |
| Equipment: | terminals 1+, 2 / 3- |
| Supply: Voltage Uo: | 25.8 V |
| Supply: Current Io: | 112 mA |
| Supply: Power Po: | 720 mW |
| Output I, II: | terminals 10, 11, 12; 16, 17, 18 non-intrinsically safe |
| Supply: Maximum safe voltage: | 253 V AC / 40 V DC (Attention! Um is no rated voltage.) |
| Supply: Contact loading: | 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load (TÜV 01 ATEX 1701) |
| Output III: | terminals 8+, 7- non-intrinsically safe |
| Supply: Maximum safe voltage Um: | 40 V (Attention! The rated voltage can be lower.) |
| Interface: | RS 232 |
| Supply: Maximum safe voltage: | 40 V (Attention! The rated voltage can be lower.) , RS 232 |
| Certificate: | TÜV 02 ATEX 1885 X |
| Supply: Marking: | II 3G Ex nA nC IIC T4 |
| Output I, II: Contact loading: | 50 V AC/2 A/cos φ > 0.7; 40 V DC/1 A resistive load |
| Galvanic isolation: Input/Other circuits: | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| FM approval: Control drawing: | 16-554FM-12 (cFMus) |
| UL approval: | E223772 |
| IECEx approval: | IECEx TUN 09.0007 |
| FM approval: Approved for: | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
| Optional accessories: | - power feed module KFD2-EB2(.R4A.B)(.SP) - universal power rail UPR-03(-M)(-S) - profile rail K-DUCT-BU(-UPR-03) - FDT framework PACTware 4.1 - device type manager DTM Interface Technology - adapter K-ADP-USB |
Логистические характеристики
| ТН ВЭД: | |
| Страна происхождения: | SG |
| EAN: | |
| Вес: | 0,00 kg |
| Длина: | 0,00 m |
| Ширина: | 0,00 m |
| Высота: | 0,00 m |