Pepperl+Fuchs
204304
HIC2065
Pepperl+Fuchs 204304
HIC2065
Voltage Repeater
Описание
1-channel isolated barrier, 24 V DC supply (bus powered), Voltage input 0 mV .. ± 50 mV, Voltage output 0 mV .. ± 50 mV, Selectable up/downscale sensor breakage detection, Fault output signal, Transfer direction: to the control systempa. This isolated barrier is used for intrinsic safety applications. It transfers low voltage signals from thermocouples, load cells, strain gauges, operational amplifiers, and inductive oscillation sensors located in hazardous areas to safe areas. The input voltage of the terminals 5a and 5b is transferred to the terminals 7a and 8a. The input, output, and power supply are galvanically isolated from each other. Upscale or downscale lead breakage monitoring is selectable via switches located on the front panel of the device. Note:. This unit requires three minutes after power-up to reach the accuracy cited in the technical data.
Технические характеристики
| Signal type: | Analog input |
| Connection: | SL1: 1a, 1b(-); 2a, 2b(+) |
| Rated voltage: | 20 ... 30 V DC bus powered via Termination Board |
| Ripple: | within the supply tolerance |
| Rated current: | ≤ 22 mA |
| Power dissipation/power consumption: | 0.7 W max. |
| Lockout voltage: | > 11 V DC |
| Connection side: | field side |
| Connection: | SL2: 5a(+), 5b(-) |
| Input resistance: | ≥ 16 MΩ |
| Transmission range: | 0 ... ± 50 mV |
| Offset voltage/current: | ≤ 5 µV / ≤ 5 nA |
| Connection side: | control side |
| Connection: | SL1: 8a(+), 7a(-) |
| Voltage: | 0 ... ± 50 mV |
| Load: | Accuracy figures for infinite load impedance. Additional 0.03 % of span for a load resistance of 10 kΩ |
| Output resistance: | max. 3 Ω |
| Line fault detection: | input: ± 100 mV output: +200 mV, -115 mV |
| Connection: | SL1: 6b |
| Output type: | open collector transistor (internal fault bus) |
| Fault voltage: | < Vcc/2 (when connected to Vcc via 10 kΩ pull up resistor) |
| Deviation: After calibration: | at 20 °C (68 °F): ± 3 µV up to ± 10mV/± 0.05 % of the span up to +50 mV/± 0.05 % of the span up to -50 mV |
| Deviation: Influence of ambient temperature: | ± 1 µV/K (typical ± 0.25 µV/K) |
| Absolute: | < 0.25 K at 30 V voltage supply |
| Bandwidth: | DC to > 350 Hz (-3 dB) |
| Settling time: | < 2 ms |
| Rise time/fall time: | ≤ 1 ms |
| Output/power supply: | functional insulation, rated insulation voltage 50 V AC |
| Display elements: | LEDs |
| Control elements: | DIP-switch |
| Configuration: | via DIP switches |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2006 For further information see system description. |
| Degree of protection: | IEC 60529:2001 |
| Protection against electrical shock: | UL 61010-1 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Mass: | approx. 100 g |
| Dimensions: | 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 inch) |
| Mounting: | on Termination Board |
| Coding: | pin 2, 3 and 4 trimmed For further information see system description. |
| EU-type examination certificate: | BASEEFA 10 ATEX 0031X |
| Electromagnetic compatibility: Marking: | II (1)GD, I (M1), [Ex ia] IIC, [Ex iaD], [Ex ia] I (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2] |
| Electromagnetic compatibility: Voltage: | 5.5 V DC |
| Electromagnetic compatibility: Current: | 2.4 mA |
| Electromagnetic compatibility: Power: | 3.3 mW |
| Supply: Maximum safe voltage: | 253 V (Attention! The rated voltage can be lower.) |
| Certificate: | BASEEFA 10 ATEX 0032X |
| Supply: Marking: | II 3G Ex nA II T4 |
| Galvanic isolation: Input/Output: | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Galvanic isolation: Input/power supply: | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| UL approval: Control drawing: | 116-0317 (cULus) |
| IECEx approval: | IECEx BAS 10.0012X IECEx BAS 10.0013X |
| UL approval: Approved for: | [Zone 0] [Ex ia] IIC, [Ex iaD], [Ex ia] I Ex nA II T4 |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
Логистические характеристики
| ТН ВЭД: | |
| Страна происхождения: | Singapur |
| EAN: | 4050143073368 |
| Вес: | 0,12 kg |
| Длина: | 0,00 m |
| Ширина: | 0,00 m |
| Высота: | 0,00 m |