Pepperl+Fuchs
203645
KFD2-STC5-Ex2
Pepperl+Fuchs 203645
KFD2-STC5-Ex2
SMART Transmitter Power Supply
Описание
This isolated barrier is used for intrinsic safety applications. 2-channel isolated barrier, 24 V DC supply (Power Rail), Input 2-wire and 3-wire SMART transmitters and 2-wire SMART current sources, Output 0/4 mA ... 20 mA current sink/current source, Terminals with test points, Up to SIL 2 acc. to IEC 61508pa. The device supplies 2-wire and 3-wire SMART transmitters, and can also be used with 2-wire SMART current sources. It transfers the analog input signal to the safe area as an isolated current value. Digital signals may be superimposed on the input signal in the hazardous or non-hazardous area and are transferred bi-directionally. The device provides a sink mode or a source mode output on the safe area terminals. The device has an internal resistor. Use this resistor if the HART communication resistance in the control circuit is too low. Test sockets for the connection of HART communicators are integrated into the terminals of the device.
Технические характеристики
| Signal type: | Analog input |
| Safety Integrity Level (SIL): | SIL 2 |
| Connection: | Power Rail or terminals 14+, 15- |
| Rated voltage: | 18 ... 30 V DC |
| Ripple: | within the supply tolerance |
| Power dissipation: | ≤ 1.4 W at maximum load |
| Power consumption: | ≤ 2.6 W at maximum load |
| Connection side: | field side |
| Connection: | terminals 1+, 2-, 3; 4+, 5-, 6 |
| Input signal: | 0/4 ... 20 mA |
| Input resistance: | max. 265 Ω terminals 2-, 3; 5-, 6 , max. 330 Ω terminals 1+, 3; 4+, 6 |
| Available voltage: | ≥ 16 V at 20 mA , terminals 1+, 3; 4+, 6 |
| Connection side: | control side |
| Connection: | terminals 7+, 8-, 9-; 10+, 11-, 12- (sink) terminals 7-, 8+, 9+; 10-, 11+, 12+ (source) see additional information |
| Load: | 0 ... 600 Ω |
| Output signal: | 0/4 ... 20 mA (overload > 25 mA) |
| Ripple: | max. 50 µA rms |
| External supply (loop): | 2 ... 30 V DC |
| Deviation: | at 20 °C (68 °F), 0/4 ... 20 mA ≤ 10 µA incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage |
| : Influence of ambient temperature: | ≤ 0.25 µA/K |
| Frequency range: | field side into the control side: band width with 1 Vpp signal 0 ... 7.5 kHz (-3 dB) safe area to hazardous area: band width with 1 VSS signal 0.3 ... 7.5 kHz (-3 dB) |
| Settling time: | 200 µs |
| Rise time/fall time: | 100 µs |
| Output/power supply: | functional insulation, rated insulation voltage 50 V AC |
| Output/Output: | functional insulation, rated insulation voltage 50 V AC |
| Display elements: | LED |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2012 EN 61326-3-2:2008 |
| Degree of protection: | IEC 60529:2001 |
| Protection against electrical shock: | UL 61010-1:2012 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Connection: | screw terminals |
| Mass: | approx. 200 g |
| Dimensions: | 20 x 124 x 115 mm (0.8 x 4.9 x 4.5 inch) , housing type B2 |
| Mounting: | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| EU-Type Examination Certificate: | CML 17 ATEX 2031X |
| Electromagnetic compatibility: Marking: | II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
| Electromagnetic compatibility: Input: | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I |
| Supply: Maximum safe voltage: | 250 V (Attention! The rated voltage can be lower.) |
| Equipment: | terminals 1+, 3-; 4+, 6- |
| Supply: Voltage Uo: | 26.2 V |
| Supply: Voltage Uq: | 27.25 V |
| Supply: Current Io: | 93 mA |
| Supply: Power Po: | 634 mW |
| Equipment: | terminals 2-, 3+; 5-, 6+ |
| Supply: Voltage Ui: | 30 V |
| Supply: Current Ii: | 115 mA |
| Supply: Power Pi: | max 1 W |
| Supply: Voltage Uo: | 2 V |
| Supply: Current Io: | 8.5 mA |
| Supply: Power Po: | 4.3 mW |
| Equipment: | terminals 1+, 2/3-; 4+, 5/6- |
| Supply: Voltage Uo: | 26.2 V |
| Supply: Voltage Uq: | 27.25 V |
| Supply: Current Io: | 115 mA |
| Supply: Power Po: | 784 mW |
| Certificate: | CML 17 ATEX 3030X |
| Supply: Marking: | II 3G Ex ec IIC T4 Gc |
| Galvanic isolation: Input/Output: | safe electrical isolation acc. to IEC/EN 60079-11:2012, voltage peak value 375 V |
| Galvanic isolation: Input/power supply: | safe electrical isolation acc. to IEC/EN 60079-11:2012, voltage peak value 375 V |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015 |
| UL approval: Control drawing: | 116-0439 (cULus) |
| IECEx approval: | IECEx CML 17.0016X |
| UL approval: Approved for: | [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I , Ex ec IIC T4 Gc |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
| Optional accessories: | - power feed module KFD2-EB2(.R4A.B)(.SP) - universal power rail UPR-03(-M)(-S) - profile rail K-DUCT-BU(-UPR-03) |
Логистические характеристики
| ТН ВЭД: | |
| Страна происхождения: | SG |
| EAN: | |
| Вес: | 0,00 kg |
| Длина: | 0,00 m |
| Ширина: | 0,00 m |
| Высота: | 0,00 m |