View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Wybierz język
1-Click Zapytanie
Produkt
Weidmueller
1351840000
VPU I 1+1 400V/25KA
Poproś o ofertę
Prawa autorskie do obrazu: Weidmueller
Weidmueller 1351840000
VPU I 1+1 400V/25KA
Na prośbę. Prześlij nam wiadomość e-mail z zapytaniem o cenę i dostępność.
"ucnguBrctvdgcxgt0eqo"
Opis
Parametry techniczne
| Type: | VPU I 1+1 400V/25KA |
| Order No.: | 1351840000 |
| Version: | Surge voltage arrester, Low voltage, without telecomm. contact, Single-phase, TN, IT with N, IT without N |
| GTIN (EAN): | 4050118158342 |
| Qty.: | 1 pc(s). |
| Width: | 71.2 mm |
| Width (inches): | 2.803 inch |
| Height: | 94 mm |
| Height (inches): | 3.701 inch |
| Depth: | 69 mm |
| Depth (inches): | 2.717 inch |
| Mounting dimension - height: | 75 mm |
| Net weight: | 634 g |
| Humidity: | 5 - 95% rel. humidity |
| Operating temperature, max.: | 70 °C |
| Operating temperature, min.: | -40 °C |
| Storage temperature, max.: | 80 °C |
| Storage temperature, min.: | -40 °C |
| Operating temperature: | -40 °C...70 °C |
| Storage temperature: | -40 °C...80 °C |
| Colour: | black, orange, blue |
| Design: | Installation housing; 4TE, Insta IP 20 |
| Optical function display: | green = OK; red = arrester is defective - replace |
| Protection degree: | IP20 |
| Rail: | TS 35 |
| Segment: | Power distribution |
| UL 94 flammability rating: | V-0 |
| Version: | without telecomm. contact |
| Pollution severity: | 2 |
| Surge voltage category: | IV |
| Rated voltage (AC): | 400 V |
| Voltage type: | AC |
| Max. continuous voltage, Uc (AC): | 400 V |
| Max. continuous voltage, Uc (N-PE): | 440 V |
| Low voltage network: | Single-phase, TN, IT with N, IT without N |
| Discharge current In (8/20µs) N-PE: | 100 kA |
| Discharge current Imax (8/20µs) N-PE: | 100 kA |
| Discharge current In (8/20µs) wire-PE: | 25 kA |
| Discharge current Imax (8/20µs) wire-PE: | 100 kA |
| Lightning test current Iimp (10/350 µs) (L-PE): | 25 kA |
| Lightning test current, Iimp (10/350 µs) (N-PE): | 100 kA |
| Frequency range, max.: | 60 Hz |
| Frequency range, min.: | 50 Hz |
| Fuse: | No Fuse neccessary ≤250 A gG, 250 A gL (if back up fuse > 250 A) |
| Short-circuit current rating ISCCR: | 25 kA |
| Follow-on current extinguishing capability Ifi: | Not available due for technical reasons |
| Standards: | IEC61643-11, EN61643-11 |
| Energy coordination (≤10 m): | Type I, Type II, Type III |
| Protection level Up at IN (L/N-PE): | ≤ 1.9 kV |
| Protection level Up at IN (N-PE): | ≤ 3 kV |
| Leakage current at Un: | 100 µA |
| Temporary surge voltage (over-voltage) - TOV: | 620 V |
| Number of poles: | 2 |
| Rated load current IL: | 100 A |
| Requirements category acc. to IEC 61643-11: | Type I, Type II |
| Requirements class, acc. to EN 61643-11: | T1, T2 |
| Response time: | ≤ 25 ns, ≤ 100 ns |
| Signalling contact: | No |
| Type of connection: | Screw connection |
| Stripping length, rated connection: | 15 mm |
| Tightening torque, min.: | 2 Nm |
| Tightening torque, max.: | 3 Nm |
| Clamping range, rated connection: | 16 mm² |
| Clamping range, min.: | 4 mm² |
| Clamping range, max.: | 35 mm² |
| Wire cross-section, solid, min.: | 2.5 mm² |
| Wire cross-section, solid, max.: | 16 mm² |
| Wire connection cross-section, finely stranded, min.: | 2.5 mm² |
| Wire connection cross section, finely stranded, max.: | 25 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), min.: | 2.5 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), max.: | 50 mm² |
| Connection cross-section, stranded, min.: | 2.5 mm² |
| Connection cross-section, stranded, max.: | 50 mm² |
| Long specification: | Multi-pin lightning arrestor according to the requirements of Class I in accordance with IEC 61643-11, EN61643-11:2013. On interface transition from 0 to 1 (in accordance with 1312-1), the arrestor, consisting of V0 material, serves as lightning protection providing equipotential bonding and is used in applications in accordance with IEC 61643-12. The use of a non-blow-out sparkover gap, in combination with a high-power varistor, satisfies the inspection requirements for Class I surge protection systems in accordance with the VDEW (Association of German Power Stations) directive. The arrestor is installed in the vicinity of the power supply for the equipment that needs protection, in a standard installation/electrical distribution enclosure. The VPU I 1+1 400 V/25 kA is used in the single-phase mains network. With thermal separation device on the varistor. If protection is no longer available, the colour in the display window changes from green to red. Rated voltage: 400 VAC lightning test current (10/350 µs) |
| Short specification: | Class I arrester for LPL 1 with 25 kA suitable for 400/690 V single-phase mains systems. Protection level < 1.9 kV. Type: Weidmüller VPU I 1+1 400 V/25 kA Order no. 1351840000 or equivalent |
| ETIM 6.0: | EC000941 |
| ETIM 7.0: | EC000941 |
| eClass 9.0: | 27-13-08-05 |
| eClass 9.1: | 27-13-08-05 |
| eClass 10.0: | 27-13-08-05 |
| UNSPSC: | 30-21-19-22 |
| ROHS: | Conform |
| Type: | VPU I 1+1 400V/25KA |
| Order No.: | 1351840000 |
| Version: | Surge voltage arrester, Low voltage, without telecomm. contact, Single-phase, TN, IT with N, IT without N |
| GTIN (EAN): | 4050118158342 |
| Qty.: | 1 pc(s). |
| Width: | 71.2 mm |
| Width (inches): | 2.803 inch |
| Height: | 94 mm |
| Height (inches): | 3.701 inch |
| Depth: | 69 mm |
| Depth (inches): | 2.717 inch |
| Mounting dimension - height: | 75 mm |
| Net weight: | 634 g |
| Humidity: | 5 - 95% rel. humidity |
| Operating temperature, max.: | 70 °C |
| Operating temperature, min.: | -40 °C |
| Storage temperature, max.: | 80 °C |
| Storage temperature, min.: | -40 °C |
| Operating temperature: | -40 °C...70 °C |
| Storage temperature: | -40 °C...80 °C |
| Colour: | black, orange, blue |
| Design: | Installation housing; 4TE, Insta IP 20 |
| Optical function display: | green = OK; red = arrester is defective - replace |
| Protection degree: | IP20 |
| Rail: | TS 35 |
| Segment: | Power distribution |
| UL 94 flammability rating: | V-0 |
| Version: | without telecomm. contact |
| Pollution severity: | 2 |
| Surge voltage category: | IV |
| Rated voltage (AC): | 400 V |
| Voltage type: | AC |
| Max. continuous voltage, Uc (AC): | 400 V |
| Max. continuous voltage, Uc (N-PE): | 440 V |
| Low voltage network: | Single-phase, TN, IT with N, IT without N |
| Discharge current In (8/20µs) N-PE: | 100 kA |
| Discharge current Imax (8/20µs) N-PE: | 100 kA |
| Discharge current In (8/20µs) wire-PE: | 25 kA |
| Discharge current Imax (8/20µs) wire-PE: | 100 kA |
| Lightning test current Iimp (10/350 µs) (L-PE): | 25 kA |
| Lightning test current, Iimp (10/350 µs) (N-PE): | 100 kA |
| Frequency range, max.: | 60 Hz |
| Frequency range, min.: | 50 Hz |
| Fuse: | No Fuse neccessary ≤250 A gG, 250 A gL (if back up fuse > 250 A) |
| Short-circuit current rating ISCCR: | 25 kA |
| Follow-on current extinguishing capability Ifi: | Not available due for technical reasons |
| Standards: | IEC61643-11, EN61643-11 |
| Energy coordination (≤10 m): | Type I, Type II, Type III |
| Protection level Up at IN (L/N-PE): | ≤ 1.9 kV |
| Protection level Up at IN (N-PE): | ≤ 3 kV |
| Leakage current at Un: | 100 µA |
| Temporary surge voltage (over-voltage) - TOV: | 620 V |
| Number of poles: | 2 |
| Rated load current IL: | 100 A |
| Requirements category acc. to IEC 61643-11: | Type I, Type II |
| Requirements class, acc. to EN 61643-11: | T1, T2 |
| Response time: | ≤ 25 ns, ≤ 100 ns |
| Signalling contact: | No |
| Type of connection: | Screw connection |
| Stripping length, rated connection: | 15 mm |
| Tightening torque, min.: | 2 Nm |
| Tightening torque, max.: | 3 Nm |
| Clamping range, rated connection: | 16 mm² |
| Clamping range, min.: | 4 mm² |
| Clamping range, max.: | 35 mm² |
| Wire cross-section, solid, min.: | 2.5 mm² |
| Wire cross-section, solid, max.: | 16 mm² |
| Wire connection cross-section, finely stranded, min.: | 2.5 mm² |
| Wire connection cross section, finely stranded, max.: | 25 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), min.: | 2.5 mm² |
| Conductor cross-section, flexible, AEH (DIN 46228-1), max.: | 50 mm² |
| Connection cross-section, stranded, min.: | 2.5 mm² |
| Connection cross-section, stranded, max.: | 50 mm² |
| Long specification: | Multi-pin lightning arrestor according to the requirements of Class I in accordance with IEC 61643-11, EN61643-11:2013. On interface transition from 0 to 1 (in accordance with 1312-1), the arrestor, consisting of V0 material, serves as lightning protection providing equipotential bonding and is used in applications in accordance with IEC 61643-12. The use of a non-blow-out sparkover gap, in combination with a high-power varistor, satisfies the inspection requirements for Class I surge protection systems in accordance with the VDEW (Association of German Power Stations) directive. The arrestor is installed in the vicinity of the power supply for the equipment that needs protection, in a standard installation/electrical distribution enclosure. The VPU I 1+1 400 V/25 kA is used in the single-phase mains network. With thermal separation device on the varistor. If protection is no longer available, the colour in the display window changes from green to red. Rated voltage: 400 VAC lightning test current (10/350 µs) |
| Short specification: | Class I arrester for LPL 1 with 25 kA suitable for 400/690 V single-phase mains systems. Protection level < 1.9 kV. Type: Weidmüller VPU I 1+1 400 V/25 kA Order no. 1351840000 or equivalent |
| ETIM 6.0: | EC000941 |
| ETIM 7.0: | EC000941 |
| eClass 9.0: | 27-13-08-05 |
| eClass 9.1: | 27-13-08-05 |
| eClass 10.0: | 27-13-08-05 |
| UNSPSC: | 30-21-19-22 |
| ROHS: | Conform |
Parametry logistyczne
| ECCN: | |
| Kraj pochodzenia: | |
| EAN: | |
| Waga: | 0,663 kg |
| Długość: | 0,00 m |
| Szerokość: | 0,00 m |
| Wysokość: | 0,00 m |