Pepperl+Fuchs 270206

VBG-PN-K30-DMD-S32-EV

AS-Interface Gateway/Safety Monitor

Na prośbę. Prześlij nam wiadomość e-mail z zapytaniem o cenę i dostępność.
"ucnguBrctvdgcxgt0eqo"

Opis

PROFINET Gateway with integrated safety monitor, double master for 2 AS-Interface networks, power supply input with decoupling coilsfa. The VBG-PN-K30-DMD-S32-EV is a PROFINET gateway with an integrated safety monitor and a double master according to AS-Interface specification 3.0. The gateway is used to connect AS-Interface systems to a higher-level PROFINET. It acts as a master for the AS-Interface segment and as a slave for the PROFINET. The AS-Interface functions are made available on both a cyclic and acyclic basis via PROFINET DP V1. The binary data of an AS-Interface segment is transferred cyclically. In addition, analog values and the complete command set of the new AS-Interface specification are transferred to PROFINET using a command interface. The gateway has six inputs and outputs. The six inputs are used for extended EDM device monitoring or as start inputs. The six outputs are semiconductor outputs and switch circuits 1 and 2. The K30 model is especially suitable for installation in a control cabinet. The device can be configured using buttons. Seven LEDs located on the front panel indicate the current status of the AS-Interface segment. One LED shows the power supply via AUX. Additional LEDs indicate the status of the inputs and outputs. Via the graphics display, the commissioning of the AS-Interface circuit and testing of the connected peripherals can take place completely independently of the commissioning of the higher-level network and programming. All functions can be controlled and shown on the display using the four buttons. An additional RJ45 Ethernet interface provides a way of exporting data relating to the gateway, network, and operation directly from the gateway for extended local diagnostic purposes. Up to 31 devices can reliably cross-communicate via the RJ45 Ethernet diagnostics interface. The integrated data decoupling function enables two AS-Interface circuits to be operated with just one standard power supply. The device features a chip card slot for storage of configuration data.

Parametry techniczne

AS-Interface specification: V3.0
PLC-Functionality: activateable
Duplicate address detection: from AS-Interface slaves
Earth fault detection: integrated
EMC monitoring: integrated
Diagnostics function: Extended function via display
Data decoupling: integrated
Switch-on delay: < 10 s
Response delay: < 40 ms
UL File Number: E223772 only from low voltage, limited energy source (SELV or PELV) or listed Class 2 source
Safety Integrity Level (SIL): SIL 3
Performance level (PL): PL e
MTTFd: 100 a
B10d: 2.5 E+5
Display: Illuminated graphical LC display for addressing and error messages
LED ETHERNET: PROFINET master detected; LED green
LED AS-i ACTIVE: AS-Interface operation normal; LED green
LED CONFIG ERR: configuration error; LED red
LED PRG ENABLE: autom. programming; LED green
LED POWER: voltage ON; LED green
LED PRJ MODE: projecting mode active; LED yellow
LED U AS-i: AS-Interface voltage; LED green
LED AUX: ext. auxiliary voltage UAUX ; LED green
LED IN: 6 x LED green
LED OUT: Output circuit closed; 6 x green LEDs
Button: 4
Switch SET: Selection and setting of a slave address
OK button: Mode selection traditional-graphical/confirmation
Button MODE: Mode selection PRJ-operation/save configuration/cursor
ESC button: Mode selection traditional-graphical/cancel
Insulation voltage: ≥ 500 V
Rated operating voltage: 26.5 ... 31.6 V from AS-Interface; 24 V DC
Rated operating current: approx. 300 mA PELV
Interface type: PROFINET I / O device (IRT)
Physical: 2 x RJ-45
Protocol: Media Redundancy Protocol (MRP)
Transfer rate: 100 MBit/s
Interface type: RJ-45 Ethernet Diagnostic Interface
Transfer rate: 10 MBit/s
Interface type: Chip card slot
Number/Type: 6 inputs Safety: 3 x 2 channels Or 6 standard inputs
Safety output: 6 semiconductor outputs Output circuits: 6 PNP transistor outputs Max. contact load: 1.2 ADC-13 at 30 VDC, Σ = 7.2 A in total (see derating)
PROFINET: RJ-45
AS-Interface: spring terminals, removable
Electromagnetic compatibility: Directive 2014/30/EU: EN 62026-2:2013 EN 61000-6-2/AC:2005, EN 61000-6-4:2007+A1:2011
Machinery Directive: Directive 2006/42/EC: EN 61508:2010 EN ISO 13849-1/AC:2009 EN 62061:2005+A1:2013
Degree of protection: EN 60529:2000
AS-Interface: EN 62026-2:2013
Noise immunity: EN 61000-6-4:2007/A1:2011 EN 61000-6-2/AC:2005
Shock resistance: EN 61131-2:2004
Functional safety: EN ISO 13849-1:2008/AC:2009, EN ISO 13849-2:2012 (up to PL e), EN 61508:2010 and EN 62061:2005+A1:2013 (up to SIL3)
UL approval: An isolated source with a secondary open circuit voltage of ≤ 30 VDC with a 3 A maximum over current protection. Over current protection is not required when a Class 2 source is employed. UL mark does not provide UL certification for any functional safety rating or aspects of the device.
Ambient temperature: 0 ... 55 °C (32 ... 131 °F)
Storage temperature: -25 ... 85 °C (-13 ... 185 °F)
Degree of protection: IP20
Material: Housing: Stainless steel
Mass: 800 g
Construction type: Low profile housing

Parametry logistyczne

ECCN:
Kraj pochodzenia: DE
EAN:
Waga: 0,89 kg
Długość: 0,00 m
Szerokość: 0,00 m
Wysokość: 0,00 m