Pepperl+Fuchs
255834
KCD2-STC-1.2O
Pepperl+Fuchs 255834
KCD2-STC-1.2O
SMART Transmitter Power Supply
Opis
1-channel signal conditioner, 24 V DC supply (Power Rail), Input for 2-wire SMART transmitters and current sources, Signal splitter (1 input and 2 outputs), Dual output 0/4 mA .. 20 mA or 0/1 V .. 5 V, Terminal blocks with test sockets, Up to SIL 2 acc. to IEC 61508pa. This signal conditioner provides the galvanic isolation between field circuits and control circuits. The device supplies 2-wire transmitters, and can also be used with current sources. The device transfers the analog input signal to the control side as two isolated output signals. Bi-directional communication is supported for SMART transmitters that use current modulation to transmit data and voltage modulation to receive data. The output is selected as a current source, current sink, or voltage source via switches. Test sockets for the connection of HART communicators are integrated into the terminals of the device.
Parametry techniczne
| Signal type: | Analog input |
| Safety Integrity Level (SIL): | SIL 2 |
| Connection: | Power Rail or terminals 9+, 10- |
| Rated voltage: | 18 ... 30 V DC |
| Ripple: | within the supply tolerance |
| Power dissipation: | approx. 1.4 W at 20 mA transfer current, 250 Ω in both outputs |
| Power consumption: | 2 W |
| Connection side: | field side |
| Connection: | terminals 1+, 2- (sink); 3+, 4- (source) |
| Input signal: | 0/4 ... 20 mA |
| Voltage drop: | terminals 3, 4: ≤ 6.1 V at 20 mA |
| Short-circuit current: | terminals 1+, 2-: 25 mA |
| Input resistance: | terminals 1+, 2-: max. 500 Ω (BRAIN) (250 Ω load) |
| Available voltage: | terminals 1+, 2-: ≥ 16 V at 20 mA , ≥ 18.5 V at 4 mA |
| Connection side: | control side |
| Connection: | source: terminals 5-, 6+; 7-, 8+ sink: terminals 5+, 6-, 7+, 8- |
| Load: | channel 1: 0 ... 500 Ω (20 mA)/> 1 MΩ (5 V) channel 2: 0 ... 500 Ω (20 mA)/> 1 MΩ (5 V) |
| Output signal: | 0/4 ... 20 mA or 0/1 ... 5 V |
| Ripple: | max. 50 µA rms |
| Deviation: | Iout < 20 µA (0.1 %); Vout < 7.5 mV (0.15 %) incl. calibration, linearity, hysteresis and fluctuation of supply voltage, at 20 °C (68 °F), 0/4 ... 20 mA, 0/1 ... 5 V |
| : Influence of ambient temperature: | current output: 0.25 µA/K voltage output: 80 µV/K |
| Frequency range: | field side into the control side: bandwidth with 0.5 Vpp signal 0 ... 7.5 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0.3 ... 7.5 kHz (-3 dB) |
| Settling time: | 6 ms |
| Rise time/fall time: | 2 ms |
| Input/Output: | basic insulation according to IEC 61010-1, rated insulation voltage 300 Veff |
| Input/power supply: | basic insulation according to IEC 61010-1, rated insulation voltage 300 Veff |
| Output/power supply: | functional insulation, rated insulation voltage 50 V AC |
| Output/Output: | functional insulation, rated insulation voltage 50 V AC |
| Display elements: | LED |
| Control elements: | DIP-switch |
| Configuration: | via DIP switches |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2012 EN 61326-3-2:2008 |
| Degree of protection: | IEC 60529:2001 |
| Protection against electrical shock: | UL 61010-1:2012 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Connection: | screw terminals |
| Mass: | approx. 100 g |
| Dimensions: | 12.5 x 114 x 122 mm (0.5 x 4.5 x 4.8 inch) , housing type A2 |
| Mounting: | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| Note: | Both output loads must be connected to ensure complete and correct operation within the technical specification. |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
| Optional accessories: | - power feed module KFD2-EB2(.R4A.B)(.SP) - universal power rail UPR-03(-M)(-S) - profile rail K-DUCT-GY(-UPR-03) |
Parametry logistyczne
| ECCN: | |
| Kraj pochodzenia: | SG |
| EAN: | |
| Waga: | 0,13 kg |
| Długość: | 0,00 m |
| Szerokość: | 0,00 m |
| Wysokość: | 0,00 m |