255404
HIDTB08-DVM-IDC4-SC-R1-SM32
Termination Board
The function of the Termination Board as well as the connector pin assignment exactly fit the requirement of DeltaV Traditional I/O systems. System board for Emerson DeltaV, For two 8-channel AI/AO/DO cards via 16-pin Mass Termination Block, For four 8-channel DI cards via 16-pin Mass Termination Block, For 8 modules/16 or 32 channels, Recommended modules: HiD2030SK (AI), HiD2038 (AO), HiD2824 (DI), HiD2844 (DI), HiD2872 (DO), Volt-free fault indication output, 24 V DC supply, Hazardous area: screw terminals, blue, Non-hazardous area: IDC connector, 16-pinpa. Information about missing supply voltage of the interface modules is available for the system as potential-free contact. Wiring errors from field will be reported via the same relay contact if the interface module supports this function. The Termination Boards are supplied with a robust glass fiber reinforced plastic housing as standard. This design permits the fast and reliable installation on 35 mm DIN mounting rail acc. to EN 60715 in the cabinet.
| Connection: | X20: terminals 3, 5(+); 4, 6(-) |
| Nominal voltage: | 24 V DC , in consideration of rated voltage of used isolators |
| Voltage drop: | 0.9 V , voltage drop across the series diode on the termination board must be considered |
| Ripple: | ≤ 10 % |
| Fusing: | 2 A , in each case for 8 modules |
| Power dissipation: | ≤ 500 mW , without modules |
| Reverse polarity protection: | yes |
| Supply: | Redundancy available. The supply for the isolators is decoupled, monitored and fused. |
| Connection: | X20: terminals 1, 2 |
| Output type: | volt-free contact |
| Contact loading: | 30 V DC , 1 A |
| Display elements: | LEDs PWR ON (Termination Board power supply) - LED power supply I, green LED - LED power supply II, green LED LED FAULT (fault indication), red LED - LED lits: module failure - LED flashes: power supply failure |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2012 For further information see system description. |
| Degree of protection: | IEC 60529:2001 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Storage temperature: | -40 ... 70 °C (-40 ... 158 °F) |
| Degree of protection: | IP20 |
| Connection: Field side: | explosion hazardous area: screw terminals , blue |
| Connection: Control side: | non-explosion hazardous area: IDC plug, 16-pin |
| Connection: Supply: | pluggable screw terminals , black |
| Connection: Fault output: | pluggable screw terminals , black |
| Core cross-section: | screw terminals: 0.2 ... 2.5 mm2 (24 ... 12 AWG) |
| Material: | housing: polycarbonate, 10 % glass fiber reinforced |
| Mass: | approx. 600 g |
| Dimensions: | 150 x 200 x 163 mm (5.9 x 7.9 x 6.42 inch) , height including module assembly |
| Mounting: | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| EU-type examination certificate: | CESI 11 ATEX 062 |
| Connection: Marking: | II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
| Non-hazardous area: Maximum safe voltage: | 250 V (Attention! Um is no rated voltage.) |
| Galvanic isolation: Field circuit/control circuit: | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 50303:2000 |
| CSA approval: Control drawing: | see control drawing of correspoding modules |
| IECEx approval: | IECEx CES 11.0022 |
| CSA approval: Approved for: | [Ex ia Ga] IIC [Ex ia Da] IIIC [Ex ia Ma] I |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
| Designation: | optional accessory: Label Carrier HiALC-Hi*TB-SET-1** |
| ECCN: | |
| Kraj pochodzenia: | Singapur |
| EAN: | 4050143064267 |
| Waga: | 0,71 kg |
| Długość: | 0,00 m |
| Szerokość: | 0,00 m |
| Wysokość: | 0,00 m |