Pepperl+Fuchs
185930
HiD2024
Pepperl+Fuchs 185930
HiD2024
SMART Transmitter Power Supply/Current Driver
Opis
4-channel isolated barrier, 24 V DC supply (bus powered), Analog in or analog out signals, Sink and source mode outputs, SMART pass-through, Up to SIL 2 acc. to IEC 61508pa. This isolated barrier is used for intrinsic safety applications. It operates as a SMART transmitter power supply or as a repeater. Bi-directional communication is supported for SMART transmitters that use current modulation to transmit data and voltage modulation to receive data. The outputs are fully isolated from the inputs, the power supply, and each other. An open field circuit presents a high impedance to the control side to allow alarm conditions to be monitored by control systems. This module mounts on a HiD Termination Board.
Parametry techniczne
| Signal type: | Analog input/analog output |
| Safety Integrity Level (SIL): | SIL 2 |
| Connection: | SL1: 1a(-), 1b(-); 2a(+), 2b(+) |
| Rated voltage: | 20.4 ... 30 V DC bus powered via Termination Board |
| Ripple: | ≤ 10 % |
| Rated current: | 140 mA at 24 V and 20 mA |
| Power dissipation: | ≤ 1.8 W at 20 mA |
| Power consumption: | ≤ 3.3 W at 20 mA |
| Connection: | SL1: 8a(+), 7a(-); 10a(+), 9a(-); 9b(+), 10b(-); 8b(+), 7b(-) |
| Voltage drop: | approx. 6 V or internal resistance 300 Ω at 20 mA |
| Ripple: | 200 mV eff |
| Input: Signal: | 4 ... 20 mA |
| Input: Resistor: | > 100 kΩ at max. 23 V, with field wiring open |
| Output: Signal: | 4 ... 20 mA or 1 ... 5 V (on 250 Ω, 0.1 % internal shunt) 4 ... 20 mA (sink mode), operating voltage 15 ... 26 V |
| Output: Load: | 0 ... 300 Ω (source mode) |
| Connection: | SL2: 5a(+), 5b(-); 1a(+), 1b(-); 3a(+), 3b(-); 7a(+), 7b(-) |
| Voltage: | ≥ 15 V at 20 mA |
| Input: Signal: | 4 ... 20 mA , limited to approx. 30 mA |
| Output: Signal: | 4 ... 20 mA |
| Output: Load: | 0 ... 650 Ω |
| Deviation: | at 20 °C (68 °F) ≤ ± 0.1 % incl. non-linearity and hysteresis (source mode 4 ... 20 mA) ≤ ± 0.2 % incl. non-linearity and hysteresis (sink mode 4 ... 20 mA) ≤ ± 0.2 % incl. non-linearity and hysteresis (source mode 1 ... 5 V) ≤ ± 0.2 % incl. non-linearity and hysteresis (analog output mode 4 ... 20 mA) |
| Frequency range: | field side into the control side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB) |
| Rise time: | 10 to 90 % ≤ 20 ms |
| Display elements: | LED |
| Control elements: | DIP-switch potentiometer |
| Configuration: | via DIP switches via potentiometer |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2006 For further information see system description. |
| Degree of protection: | IEC 60529 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Mass: | approx. 140 g |
| Dimensions: | 18 x 106 x 128 mm (0.7 x 4.2 x 5 inch) |
| Mounting: | on Termination Board |
| EU-Type Examination Certificate: | CESI 02 ATEX 086 |
| Electromagnetic compatibility: Marking: | II (1)G [Ex ia Ga] IIC , II (1)D [Ex ia Da] IIIC |
| Certificate: | PF 11 CERT 2109 X |
| Electromagnetic compatibility: Marking: | II 3G Ex nA IIC T4 Gc |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| IECEx approval: | IECEx TUN 04.0012 |
| Directive conformity: Approved for: | [Ex ia] IIC |
Parametry logistyczne
| ECCN: | |
| Kraj pochodzenia: | SG |
| EAN: | |
| Waga: | 0,00 kg |
| Długość: | 0,00 m |
| Szerokość: | 0,00 m |
| Wysokość: | 0,00 m |