View this page in: English
Email: "ucnguBrctvdgcxgt0eqo"
Wybierz język
1-Click Zapytanie
Produkt
Pepperl+Fuchs
321749
HIC2025Y1
Poproś o ofertę
Pepperl+Fuchs 321749
HIC2025Y1
SMART Transmitter Power Supply
Na prośbę. Prześlij nam wiadomość e-mail z zapytaniem o cenę i dostępność.
"ucnguBrctvdgcxgt0eqo"
Opis
1-channel isolated barrier, 24 V DC supply (bus powered), Input for 2-wire SMART transmitters, Output for 4 mA .. 20 mA or 1 V .. 5 V, Low power dissipation, Up to SIL 2 acc. to IEC 61508pa. This isolated barrier is used for intrinsic safety applications. The device supplies 2-wire transmitters in the hazardous area. The device transfers the analog input signal to the non-hazardous area as an isolated current value. Bi-directional communication is supported for SMART transmitters that use current modulation to transmit data and voltage modulation to receive data. The output is selected as a current source, current sink, or voltage source via DIP switches. This device mounts on a HiC Termination Board.
Parametry techniczne
| Signal type: | Analog input |
| Safety Integrity Level (SIL): | SIL 2 |
| Connection: | SL1: 1a, 1b(-); 2a, 2b(+) |
| Rated voltage: | 19 ... 30 V DC bus powered via Termination Board |
| Ripple: | ≤ 10 % |
| Rated current: | ≤ 45 mA |
| Power dissipation: | ≤ 800 mW |
| Power consumption: | ≤ 1.1 W |
| Connection side: | field side |
| Connection: | SL2: 5a(+), 5b(-) |
| Input signal: | 4 ... 20 mA limited to approx. 30 mA |
| Available voltage: | ≥ 15 V at 20 mA on SL2: 5a(+), 5b(-) |
| Connection side: | control side |
| Connection: | SL1: 8a(+), 7a(-) |
| Load: | 0 ... 300 Ω (source mode) |
| Output signal: | 4 ... 20 mA or 1 ... 5 V (on 250 Ω, 0.1 % internal shunt) 4 ... 20 mA (sink mode), operating voltage 15 ... 26 V |
| Ripple: | 20 mV rms |
| Deviation: | at 20 °C (68 °F) ≤ ± 0.1 % incl. non-linearity and hysteresis (source mode 4 ... 20 mA) ≤ ± 0.2 % incl. non-linearity and hysteresis (sink mode 4 ... 20 mA) ≤ ± 0.2 % incl. non-linearity and hysteresis (source mode 1 ... 5 V) |
| : Influence of ambient temperature: | < 2 µA/K (0 ... 60 °C (32 ... 140 °F)); < 4 µA/K (-20 ... 0 °C (-4 ... 32 °F)) |
| Frequency range: | field side into the control side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 Vpp signal 0 ... 3 kHz (-3 dB) |
| Settling time: | ≤ 200 ms |
| Rise time/fall time: | ≤ 20 ms |
| Input/Output: | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Input/power supply: | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Output/power supply: | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff |
| Display elements: | LED |
| Control elements: | DIP-switch |
| Configuration: | via DIP switches |
| Labeling: | space for labeling at the front |
| Electromagnetic compatibility: Directive 2014/30/EU: | EN 61326-1:2013 (industrial locations) |
| Electromagnetic compatibility: | NE 21:2006 For further information see system description. |
| Degree of protection: | IEC 60529:2001 |
| Ambient temperature: | -20 ... 60 °C (-4 ... 140 °F) |
| Degree of protection: | IP20 |
| Mass: | approx. 100 g |
| Dimensions: | 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 inch) |
| Mounting: | on Termination Board |
| Coding: | pin 1 and 3 trimmed For further information see system description. |
| EU-type examination certificate: | CESI 06 ATEX 017 |
| Electromagnetic compatibility: Marking: | II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I |
| Electromagnetic compatibility: Input: | Ex ia |
| Supply: Maximum safe voltage: | 250 V AC (Attention! Um is no rated voltage.) |
| Equipment: | SL2: 5a(+), 5b(-) |
| Supply: Voltage Uo: | 25.2 V |
| Supply: Current Io: | 100 mA |
| Supply: Power Po: | 630 mW |
| Supply: Internal capacitance Ci: | 5.7 nF |
| Supply: Internal inductance Li: | negligible |
| Certificate: | KIWA 15 ATEX 0035 X |
| Supply: Marking: | II 3G Ex ec IIC T4 Gc |
| Directive conformity: Directive 2014/34/EU: | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015+A1:2018 , EN 50303:2000 |
| FM approval: Control drawing: | 16-534FM-12 (cFMus) |
| IECEx approval: IECEx certificate: | IECEx CES 06.0002 IECEx KIWA 15.0017X |
| IECEx approval: IECEx marking: | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex ec IIC T4 Gc |
| Supplementary information: | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
Parametry logistyczne
| ECCN: | |
| Kraj pochodzenia: | Singapur |
| EAN: | 4050143070572 |
| Waga: | 0,00 kg |
| Długość: | 0,00 m |
| Szerokość: | 0,00 m |
| Wysokość: | 0,00 m |